Model reference
Jenn-Air JGW8130DDW
Oven
6 documents40 error codes29 service modes
Available documentation
Tech Sheet
- Tech Sheet - 16022515F (FR)12 pg
Service Manual
- Service Manual - 1602251460 pg
- Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
- FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
Installation Guide
- Installation Instructions24 pg
Other
- Jenn Air60 pg
MyPros+ Max
Diagnose your Jenn-Air JGW8130DDW.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (40)
CodeMeaning
1c1cShorted key detected on the control circuit board keyboard.1c2cKeyboard tail disconnected or keyboard loop has improper value.1c31Cancel key circuit problem (cancel key improper value) on upper/single oven…1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cPower micro communication failure (CRC invalid).1c5cVcc or ground fault at test point during cook or clean cycle.1c6cEEPROM error1c7cControl not calibrated1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error1d11Runaway temperature (650°F) detected with door unlocked on upper/single oven…1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway temperature (950°F) detected with door locked on upper/single oven…1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Temperature sensor failure (open) on upper/single oven cavity3d12Temperature sensor failure (open) on lower oven cavity3d21Temperature sensor failure (short) on upper/single oven cavity3d22Temperature sensor failure (short) on lower oven cavity3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failureView all 40 error codes
4d52Door switch circuit failure9d11Door latch will not lock on upper/single oven cavity9d12Door latch will not lock on lower oven cavity9d21Door latch will not unlock on upper/single oven cavity9d22Door latch will not unlock on lower oven cavity9d31Door latch both locked and unlocked simultaneously on upper/single oven9d32Door latch both locked and unlocked simultaneously on lower oven9d41Unlock condition9d51Lock and unlock state unknown9d61Door position switch open circuit detected during clean cycle.
Service modes (29)
- 12/24 Hour Clock TogglePress and hold CANCEL and FAVORITE simultaneously for 3 seconds.
- 24 Hour Clock Toggle["Press and hold CANCEL and FAVORITE pads for 3 seconds."]
- Child Lockout["Press and hold CANCEL and COOK & HOLD pads for 3 seconds.","OFF will display where the…
- Child Safety LockPress and hold CANCEL and COOK & HOLD simultaneously for 3 seconds
- Clock Display Toggle["Press and hold CANCEL and CLOCK pads for 3 seconds."]
- Clock Display Toggle (On/Off)Press and hold CANCEL and CLOCK pads for 3 seconds to toggle clock display on or off.
- Diagnostic Code DisplayEnter Quick Test Mode (CANCEL + BROIL for 3 seconds), then press COOK & HOLD to display last…
- Diagnostic Code Display Mode["Press and hold the AUTOSET (0) pad.","While holding AUTOSET pad, power up the unit.","Cycle…
- Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
- Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
- Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
- Factory Default Reset["Press and hold CANCEL and KEEP WARM pads for 3 seconds."]
- Faults Access (EOC III Controls)1
- One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
- Oven Temperature Adjustment["Press the BAKE pad.","Enter 550 on the number pads.","Immediately press and hold the BAKE pad for…
- Quick Test Mode["Press and hold CANCEL and BROIL pads simultaneously for 3 seconds.","Once control enters Quick…
- Quick Test Mode (EOC III Controls)1
- Quick Test Mode (H1 Controls - Convection Model)1
- Quick Test Mode (H1 Controls - Non-Convection Model)1
- Quick Test Mode (H2/H2.5 Controls)1
- Quick Test Mode (H3 Controls)1
- Quick Test Mode (M1/M2 Controls)1
- Quick Test Mode (NSC Non-Self Clean Controls)1
- Sabbath Mode["Press and hold CLOCK button for 3 seconds to activate Sabbath Mode.","SAb will be displayed and…
- Service Mode (EOC III Controls)1
- Temperature Calibration Adjustment1
- Temperature Display (F/C toggle)Press and hold CANCEL and BAKE simultaneously for 3 seconds.
- Temperature Display Toggle (F/C)["Press and hold CANCEL and BAKE pads for 3 seconds."]
- Test Mode (UH Controls)1
Full entry steps, exit procedures, and test sequences are available in Max.
Related Jenn-Air oven models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass