Model reference

Jenn-Air JJW2424HL0

Oven

6 documents32 error codes7 service modes

Available documentation

Service Manual

JennAir® 60 cm Built-In Convection Oven Technical Manual32 pg
Covers this model

Tech Sheet

tech sheet w11686738 revA2 pg
Covers this model

Tech Tip

Instruction Sheet1 pg
Covers this model

Installation Guide

Installation Instructions24 pg
Covers this model
Wire-Diagram2 pg
Covers this model
Trim Kit12 pg
Covers this model

MyPros+ Max

Diagnose your Jenn-Air JJW2424HL0.

Step-by-step diagnostics from the service manual
Test values, resistance specs, and wiring references
Verified part numbers when replacement is needed

Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Jenn-Air Oven

CONFIGURATION_PARAMETERS_MYSMATCH_WITH_HW on my Jenn-Air JJW2424HL0

M+

Configuration parameters mismatch with

From Tech Sheet W17259481, p.13:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure control board supply voltage at test points. Expected: 12 VDC and 5 VDC.

3.Inspect all connectors on the main control for corrosion or backed-out pins.

Part WPW10804018

Electronic control board

Error codes (32)

CodeMeaning

CONFIGURATION_PARAMETERS_MYSMATCH_WITH_HWConfiguration parameters mismatch with hardware.F1E1Internal oven Appliance Manager error F1E3ADC_DIAG F2E1ADC_DIAG F2E2Keypad/Display Disconnected.F2E4HMI Over Temperature.F2E5HMI Fault.F3E0Main oven sensor open or shorted (open if temperature above 1112°F/600°C…F3E3Oven meat probe open or shorted.F4E1Temperature Error F4E2Magnetron Temp Sensor Error.F4E4Humidity Sensor Error F4E7MWO Meat Probe/Temperature Probe connector or probe Failure.F5E0Door and Latch Switch do not agree (main/upper oven).F5E1Latch not operating (main/upper oven)F5E2Door Switch MWO.F6E0Communication between controls F6E1Over temperature (main/upper oven). Note F6E4User Interface/Appliance Manager state status mismatch.F6E6Oven Appliance Manager lost communication (main/upper oven).F7E2Boiler NTC Out of Range outside the range -20°C to +145°C.F8E8This error appears if the drain pump is ON for maximum time and the water level…F9E0Product not wired correctly.FACTORY_TEST_NOT_PERFORMEDFactory test not performed.FCE1WiFi Module Connection.FCE2No link between WiFi module and wireless router.FCE3No link between WiFi module and internet.FCE4Antenna A not operational.FCE5Antenna B not operational.PEC_1_COOKINGSystem Failure

View all 32 error codes

PEC_1_IDLESystem Failure PEC_3_FAILSystem Failure

Service modes (7)

Component Activation["Enter Diagnostics Mode.","Touch or scroll to 'Component Activation' in the Diagnostics…
Diagnostics Mode["Press 'Setting', scroll down and press 'Info.'","Press 'Service and Support.'","Check that the…
Error Diagnostic["Enter Diagnostics Mode.","Press 'Error Diagnostic' to see the last error detected."]
Sensors and Switches View["Enter Diagnostics Mode.","View current status of oven switches and sensor readings
Service Diagnostic Mode / Component Activation["1
System Info["Enter Diagnostics Mode.","Select 'System Info.'"]
UI Configuration Mode["Press 'Setting,' scroll down and press 'Info.'","Press 'Service and Support.'","Check that the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Jenn-Air oven models

78,000+ service manuals · 160,000+ error codes · 55+ brands

$29/month · Cancel anytime · Or $9.95 3-day pass