mypros+
Error code reference

Jenn-Air Oven Error Code F3E0

Main oven sensor open or shorted (open if temperature above 1112°F/600°C, shorted if below -4°F/-20°C).

Jenn-Air codesJenn-Air oven codes

Main oven sensor open or shorted (open if temperature above 1112°F/600°C, shorted if below -4°F/-20°C).

First step from the service manual

Unplug oven or disconnect power. Check the sensor probe, cable, and connector (J64 in microwave section, J62 in oven section). Check the whole board connection harness for loose or damaged connections.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F3E0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F3E0 means on a Jenn-Air oven

The F3E0 error code on a Jenn-Air oven indicates a fault with the main oven temperature sensor, also called the oven probe or RTD (resistance temperature detector). The control board monitors the sensor's resistance to determine oven temperature. When the board reads a resistance value that corresponds to a temperature above 1112°F (600°C), it interprets the sensor circuit as open (broken circuit). When the reading corresponds to a temperature below -4°F (-20°C), it interprets the circuit as shorted (a direct low-resistance connection that bypasses normal signal range). Neither condition reflects actual oven temperature; instead, they reflect a fault in the sensor itself or the wiring between the sensor and the control board.

The sensor probe is located inside the oven cavity and connects to the control board through a wiring harness. Two key connectors are involved: J64 in the microwave section and J62 in the oven section. A fault can originate at the probe itself, along the cable run, or at either connector. Loose pins, heat-damaged insulation, corrosion at connector terminals, or a physically failed sensor element can all produce an F3E0 condition. Because the harness runs through areas exposed to heat cycling over time, connector degradation is a common contributor alongside outright sensor failure.

Source: manufacturer service documentation.

Common causes of F3E0

  1. 01

    Failed oven temperature sensor

    Part replacement

    The sensor probe itself has an open or shorted internal element, producing a resistance value outside the normal operating range. This is the most frequent cause and can be confirmed by measuring the sensor's resistance with a multimeter after disconnecting it from the harness.

  2. 02

    Loose or corroded connector at J62 or J64

    Wiring / connection

    The connectors at J62 (oven section) and J64 (microwave section) can develop loose pins or corroded terminals over time, interrupting the sensor signal. Inspect both connectors for discoloration, bent pins, or terminals that do not seat firmly.

  3. 03

    Damaged sensor wiring or cable

    Part replacement

    The cable running from the sensor probe to the control board can suffer insulation damage from heat exposure, resulting in a short or open circuit along the run. Visually inspect the full cable length for melted, pinched, or chafed insulation.

  4. 04

    Loose connection at the main board harness

    Wiring / connection

    A loose or improperly seated harness connector at the control board can cause the same open or short symptoms as a failed sensor. Check all board-side connectors for secure seating before assuming the sensor has failed.

  5. 05

    Faulty control board

    Part replacement

    If the sensor and all wiring check out correctly, the control board itself may be misreading the sensor signal due to a failed input circuit. This is the least common cause and should only be considered after ruling out the sensor and harness.

See the test procedure for each cause

Frequently asked questions about F3E0

What does F3E0 mean on a Jenn-Air oven?
F3E0 indicates that the main oven temperature sensor circuit is reading outside its normal range. The control board sees either an open circuit (corresponding to a temperature above 1112°F/600°C) or a shorted circuit (corresponding to a temperature below -4°F/-20°C). This prevents the oven from operating because it cannot confirm actual cavity temperature. The fault can involve the sensor probe, the connecting cable, or the harness connectors at J62 and J64.
Can I fix F3E0 myself, or do I need a technician?
A knowledgeable DIYer can begin diagnosis by unplugging the oven and visually inspecting the sensor, cable, and connectors for obvious damage or loose connections. If the sensor needs replacement, it is generally a straightforward part swap that does not require specialized tools. However, if the wiring is damaged inside the oven cavity or the control board is at fault, a professional technician is recommended to ensure a safe repair.
Is it safe to use my Jenn-Air oven while F3E0 is displayed?
No, you should not use the oven while F3E0 is active. The control board cannot monitor actual oven temperature without a functioning sensor, which means it cannot regulate heat properly or prevent overheating. Disconnect power to the oven and resolve the fault before resuming use.
Will resetting the oven clear the F3E0 error code?
Unplugging the oven and restoring power may temporarily clear the code, but it will return as soon as the control board checks the sensor again and finds the same out-of-range reading. A reset does not fix the underlying problem. The sensor, wiring, or connectors must be inspected and repaired for the code to clear permanently.
How much does it cost to repair a Jenn-Air oven with an F3E0 error?
If only the sensor probe needs replacement, parts typically range from around $20 to $80 depending on the model, plus any labor charges if a technician performs the work. A full service call with labor and parts generally falls in the range of $100 to $300. If the control board is the root cause, costs can be higher, often in the $200 to $450 range including parts and labor.

Related Jenn-Air oven codes

All Jenn-Air oven codes
View all 154 Jenn-Air oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass