mypros+
Error code reference

Jenn-Air Oven Error Code FA

Communication error between boards (display board side).

Jenn-Air codesJenn-Air oven codes

Communication error between boards (display board side).

First step from the service manual

Check J2 harness, ohm wires end to end. If harness ok, replace display board.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for FA.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What FA means on a Jenn-Air oven

The FA error code on a Jenn-Air oven indicates a communication failure originating on the display board side of the control system. Modern Jenn-Air ovens use a two-board architecture where a main control board handles the core oven functions and a separate display board manages the user interface. These two boards exchange data continuously through a dedicated wiring harness, and when that communication link breaks down on the display board side, the FA code is triggered.

The J2 harness is the primary suspect in most FA fault occurrences. This connector and its associated wiring carry the serial communication signal between the two boards. A broken wire, corroded pin, loose connector seat, or damaged harness insulation can interrupt the signal and cause the fault. Ohm testing each wire in the J2 harness end to end will confirm whether continuity is present throughout. Any wire showing an open circuit or unusually high resistance points to the harness as the root cause.

If the J2 harness passes continuity testing and all connections are seated firmly with no visible pin damage or corrosion, the display board itself is the likely failed component. The display board contains the communication circuitry that interfaces with the main control board, and an internal failure on that board will produce the same FA fault regardless of harness condition. In that scenario, replacing the display board is the appropriate corrective action.

Source: manufacturer service documentation.

Common causes of FA

  1. 01

    Faulty or loose J2 harness connection

    Wiring / connection

    The J2 wiring harness that links the display board to the main control board can develop loose connector seating, bent pins, or corrosion that breaks the communication signal. Inspect the connector at both ends and reseat it firmly before performing ohm tests on each wire.

  2. 02

    Broken or open wire in the J2 harness

    Part replacement

    Individual wires within the J2 harness can break internally due to repeated flexing, heat exposure, or physical damage, while the insulation remains visually intact. Ohm testing each wire end to end will reveal any open circuits that need repair or harness replacement.

  3. 03

    Corroded harness pins or connector terminals

    Wiring / connection

    Moisture or grease exposure near the oven cavity can cause corrosion on the J2 connector pins, increasing resistance enough to disrupt the communication signal. Corroded terminals often show visible discoloration and may require cleaning or connector replacement.

  4. 04

    Failed display board

    Part replacement

    If the J2 harness tests good and all connections are secure, the internal communication circuitry on the display board has likely failed. This is the recommended replacement step after harness integrity has been confirmed.

See the test procedure for each cause

Frequently asked questions about FA

What does FA mean on a Jenn-Air oven?
The FA code on a Jenn-Air oven signals a communication error on the display board side of the control system. The oven uses two separate boards that must exchange data continuously, and this code appears when that communication link has broken down. The fault can stem from a problem in the J2 wiring harness connecting the two boards or from a failure within the display board itself.
Will resetting the oven clear the FA error code?
A power reset by shutting off the circuit breaker for a few minutes may temporarily clear the FA code, but it will almost certainly return if the underlying cause is not addressed. The code reflects an active hardware fault in the wiring harness or display board, not a software glitch. A reset is useful for confirming the fault is persistent, but it is not a repair.
How do I fix the FA error on my Jenn-Air oven?
Start by locating the J2 harness that connects the display board to the main control board and inspect it for loose connectors, bent pins, or visible wire damage. Reseat both ends of the connector and use a multimeter to ohm test each wire end to end for continuity. If all wires pass and connections are solid, the display board will need to be replaced to resolve the fault.
Is it safe to use my Jenn-Air oven while the FA code is displayed?
Operating the oven with an active FA error is not recommended. The communication failure between the display board and the main control board means the oven may not respond reliably to controls or may behave unpredictably. It is best to discontinue use and complete the diagnosis and repair before running the appliance again.
How much does it cost to repair a Jenn-Air oven FA error?
If the issue is simply a loose connector or a repairable harness wire, the cost can be minimal, primarily covering labor time for the diagnosis. A replacement J2 harness, if needed, typically runs in the range of $20 to $60 depending on the specific model. If the display board has failed, that part generally costs between $80 and $250, with total repair costs including labor ranging from $150 to $400 or more depending on your service provider.

Related Jenn-Air oven codes

All Jenn-Air oven codes
View all 154 Jenn-Air oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass