mypros+
Error code reference

Jenn-Air Oven Error Code F3E3-0

Main cavity meat probe temp sensor shorted.

Jenn-Air codesJenn-Air oven codes

Main cavity meat probe temp sensor shorted.

First step from the service manual

Enter Diagnostics mode and verify meat probe is at room temperature (50°F to 90°F).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F3E3-0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F3E3-0 means on a Jenn-Air oven

The F3E3-0 error code on a Jenn-Air oven indicates that the main cavity meat probe temperature sensor has experienced a short circuit condition. A shorted sensor means the electrical resistance in the probe circuit has dropped abnormally low, causing the oven's control board to detect a signal that falls outside the expected operating range. The meat probe is a temperature-sensing device inserted into food during cooking, and its circuit must maintain specific resistance values that correspond to temperature readings. When a short occurs, the control interprets the out-of-range signal as a fault and halts normal operation to prevent inaccurate cooking temperatures.

The diagnostic process begins by entering the oven's diagnostics mode and confirming the meat probe is at room temperature, typically between 50°F and 90°F. At room temperature, the probe should produce a resistance reading within a predictable range. If the reading is near zero ohms or significantly below the expected value, a short is confirmed. This could exist in the probe itself, the probe socket mounted inside the oven cavity, or the wiring harness connecting the socket to the control board.

Common causes include physical damage to the probe tip or cable, contamination inside the probe port from food or grease creating an unintended conductive path, and internal failure of the probe's sensing element. The probe socket and associated wiring are also candidates, particularly if the oven has experienced moisture exposure or if the wiring insulation has degraded from prolonged heat cycling.

Source: manufacturer service documentation.

Common causes of F3E3-0

  1. 01

    Damaged or failed meat probe

    Part replacement

    The probe itself is the most frequent culprit. Physical damage to the tip, kinks in the cable, or internal failure of the sensing element can cause a short circuit within the probe. Inspect the probe cable for visible damage and test probe resistance to confirm.

  2. 02

    Food or grease contamination in the probe port

    Wiring / connection

    Grease, food debris, or moisture inside the cavity probe socket can create a conductive path that mimics a short circuit. Clean the probe port thoroughly and allow it to dry completely before retesting.

  3. 03

    Faulty probe socket or receptacle

    Part replacement

    The socket mounted inside the oven cavity can corrode, crack, or develop an internal short from heat cycling and exposure to cooking residue. If the probe tests good but the fault persists, the socket assembly may need replacement.

  4. 04

    Damaged wiring harness between probe socket and control board

    Part replacement

    The wiring connecting the probe socket to the main control board can suffer insulation breakdown from prolonged heat exposure, causing two wires to contact each other and create a short. Inspect the harness routing for damaged insulation or pinched wires.

  5. 05

    Control board fault

    Part replacement

    In less common cases, the main control board itself may be misreading the probe circuit due to a failed input component on the board. This is typically only suspected after the probe, socket, and wiring have been ruled out.

See the test procedure for each cause

Frequently asked questions about F3E3-0

What does F3E3-0 mean on a Jenn-Air oven?
F3E3-0 indicates that the main cavity meat probe temperature sensor has shorted. The oven's control board detected an abnormally low resistance signal from the meat probe circuit, which falls outside acceptable operating parameters. The oven generates this code to prevent inaccurate temperature monitoring during cooking. The fault can originate in the probe itself, the probe port, or the wiring connecting them to the control board.
Can I fix the F3E3-0 error myself?
In many cases, yes. Start by removing the meat probe, cleaning the probe port inside the oven cavity, and inspecting the probe cable for visible damage. If the probe is damaged, replacing it is a straightforward repair that most homeowners can handle. If the socket or wiring harness is the source, the repair becomes more involved and may require disassembling part of the oven cavity.
Is it safe to use my Jenn-Air oven while the F3E3-0 code is active?
If the meat probe is not inserted and the oven still displays F3E3-0, there may be a wiring or socket issue that should be addressed before continued use. If the code only appears when the probe is plugged in, you can often use the oven normally without the probe until the probe or socket is replaced. However, you should not rely on probe-based cooking modes until the fault is resolved.
Will resetting the oven clear the F3E3-0 error code?
A power reset may temporarily clear the code, but it will return if the underlying short circuit condition in the probe circuit still exists. Disconnecting the meat probe before resetting can help isolate whether the probe itself is causing the fault. A lasting fix requires identifying and correcting the source of the short.
How much does it cost to repair the F3E3-0 error on a Jenn-Air oven?
If the meat probe itself is the cause, replacement probes typically cost between $20 and $60 depending on the specific model. A probe socket or receptacle replacement part generally ranges from $30 to $80. If a service technician is needed, labor charges will add to the total cost, and control board replacement, if required, can bring the overall repair into the $150 to $400 range.

Related Jenn-Air oven codes

All Jenn-Air oven codes
View all 154 Jenn-Air oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass