mypros+
Error code reference

Jenn-Air Oven Error Code FEE9-0

Main cavity convect 2 element open circuit.

Jenn-Air codesJenn-Air oven codes

Main cavity convect 2 element open circuit.

First step from the service manual

Inspect main cavity convect element for unzipping. Ensure all connections are seated properly at element and ACU.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for FEE9-0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What FEE9-0 means on a Jenn-Air oven

Error code FEE9-0 on a Jenn-Air oven indicates an open circuit condition in the main cavity convection 2 element. An open circuit means the electrical path through the element has been broken, preventing current from flowing and rendering the element non-functional. The appliance control unit (ACU) continuously monitors the convection heating elements and triggers this fault when it detects that the circuit associated with the secondary convection element in the main cavity is incomplete.

The most common physical cause of this fault is a condition technicians refer to as "unzipping," where the heating coil inside the element separates or breaks apart internally. This can happen gradually due to thermal stress from repeated heating and cooling cycles, or suddenly due to a localized hot spot or power surge. When the element unzips, the resistance through the coil becomes infinite, and the ACU registers an open circuit. Visually, a failed element may show a visible break, burn mark, or bubbling in the outer sheath.

Loose or corroded electrical connections at either the element terminals or the ACU connector can also produce an open circuit reading without the element itself being faulty. Before condemning the element, technicians should inspect all wiring connections at both ends of the circuit, reseat any connectors that appear loose or oxidized, and verify continuity through the element using a multimeter. If the element measures infinite resistance (OL), replacement is required. If continuity is present, focus the diagnosis on the wiring harness and ACU connections.

Source: manufacturer service documentation.

Common causes of FEE9-0

  1. 01

    Failed convection element (unzipped)

    Part replacement

    The heating coil inside the convection 2 element has broken apart internally, creating an open circuit. Look for visible breaks, burn marks, or bubbling on the element sheath, and confirm with a continuity test showing infinite resistance.

  2. 02

    Loose connection at the element terminals

    Wiring / connection

    The wiring connectors at the element itself may have loosened due to vibration or repeated thermal expansion and contraction. Inspect and firmly reseat all connections at the element terminals.

  3. 03

    Loose or faulty connection at the ACU

    Wiring / connection

    The wiring harness connector at the appliance control unit may be unseated or corroded, interrupting the circuit signal. Disconnect and reseat the relevant connector at the ACU and inspect the terminal pins for damage or oxidation.

  4. 04

    Damaged wiring harness

    Part replacement

    The wiring between the ACU and the convection element may have chafed, burned, or broken along its run. Visually trace the harness for heat damage, pinching, or broken insulation and test for continuity through each wire.

  5. 05

    Failed appliance control unit (ACU)

    Part replacement

    If the element and all wiring test good but the fault persists, the ACU itself may have a failed output circuit for the convection 2 element. This is the least likely cause and should only be suspected after all other components have been ruled out.

See the test procedure for each cause

Frequently asked questions about FEE9-0

What does FEE9-0 mean on a Jenn-Air oven?
FEE9-0 indicates an open circuit in the main cavity convection 2 element. The appliance control unit has detected that the electrical circuit to this specific convection heating element is broken and no current can flow through it. The oven will not be able to use that element for heating until the fault is resolved.
Can I fix the FEE9-0 error myself?
A knowledgeable DIYer can start by checking that all wiring connections at the convection element and ACU are firmly seated, which requires no parts and may clear the fault if a loose connection is the cause. If the element itself has failed, replacing a convection heating element is a moderate-difficulty repair that involves working inside the oven cavity and disconnecting high-voltage wiring. If you are not comfortable working with electrical components in a range or oven, a qualified technician should perform the repair.
Is it safe to use my Jenn-Air oven while FEE9-0 is displayed?
The oven may still be able to operate using other heating elements, but convection baking functions that rely on the faulty element will not work correctly. Operating the oven with a known open circuit fault is generally not recommended, as continued use could mask further wiring issues. Have the fault diagnosed and repaired before relying on the oven for normal use.
Will resetting the oven clear the FEE9-0 error code?
Resetting the oven by disconnecting power for a few minutes may temporarily clear the error code display, but the fault will return as soon as the ACU runs its diagnostic cycle and detects the open circuit again. A reset does not repair a broken element or a loose connection. The underlying cause must be corrected for the error to stay cleared.
How much does it cost to repair a FEE9-0 error on a Jenn-Air oven?
If only a connection needs to be reseated, there may be no parts cost involved, though a service call fee will typically apply. If the convection element requires replacement, parts and labor costs combined generally range from around $150 to $350 or more depending on the specific model and local labor rates. If the ACU is at fault, that repair is typically more expensive, often ranging from $300 to $600 or higher.

Related Jenn-Air oven codes

All Jenn-Air oven codes
View all 154 Jenn-Air oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass