mypros+
Error code reference

Jenn-Air Oven Error Code F1E1-A

Main ACU fault

Jenn-Air codesJenn-Air oven codes

Main ACU fault — Pin short detected, can be caused by contamination on the surface of the PCB (DLB, Cavity Temp sensors, etc.).

First step from the service manual

Unplug range or disconnect power. Inspect connections to main control for loose/unplugged connectors.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F1E1-A.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F1E1-A means on a Jenn-Air oven

The F1E1-A error code on a Jenn-Air oven indicates a Main ACU (Appliance Control Unit) fault, specifically a pin short detected within the control board circuit. The ACU is the primary electronic control module that manages all oven functions, including temperature regulation, sensor communication, and operational logic. When the board detects an unintended electrical short at one of its connection pins, it triggers this fault code and interrupts normal operation to prevent further damage.

The most common underlying cause of this fault is contamination on the surface of the PCB (printed circuit board). Grease, moisture, or other residue can create conductive pathways between adjacent pins or traces on the board, simulating a short circuit even when no wiring or component has actually failed. Components most frequently involved include the DLB (door latch board) connector pins and the cavity temperature sensor input pins, both of which connect directly to the ACU.

Loose or unplugged connectors at the main control board can also contribute to this fault by creating intermittent contact or allowing pin misalignment that registers as a short. Before assuming the control board itself has failed, a thorough inspection of all harness connections to the ACU is essential, along with a careful visual examination of the board surface for any visible contamination, corrosion, or burn marks near the affected pins.

Source: manufacturer service documentation.

Common causes of F1E1-A

  1. 01

    PCB surface contamination

    Wiring / connection

    Grease, moisture, or residue on the printed circuit board can create conductive bridges between pins, triggering a false short detection. Inspect the ACU board surface visually for any oily film, corrosion, or discoloration near connector pins.

  2. 02

    Loose or disconnected ACU connectors

    Wiring / connection

    Harness connectors to the main control board can loosen over time due to vibration or heat cycling, causing intermittent pin contact that registers as a short. After disconnecting power, check all connectors to the ACU and reseat any that feel loose or appear partially unseated.

  3. 03

    Faulty cavity temperature sensor wiring

    Part replacement

    The cavity temperature sensor circuit connects directly to the ACU, and damaged or pinched wiring in that harness can produce a pin short reading. Inspect the sensor wiring for any visible damage, melting, or contact with the oven cavity walls.

  4. 04

    DLB (door latch board) connection fault

    Part replacement

    The door latch board communicates with the ACU through a dedicated connector, and a fault in that connection, including contamination or damaged wiring, can trigger the F1E1-A code. Check the DLB connector and harness for corrosion or physical damage.

  5. 05

    Failed main ACU (control board)

    Part replacement

    If contamination is not present and all connections are secure, the ACU itself may have an internal short or failed component on the board. A failed control board requires full replacement and is typically diagnosed after all other causes are ruled out.

See the test procedure for each cause

Frequently asked questions about F1E1-A

What does F1E1-A mean on a Jenn-Air oven?
The F1E1-A code on a Jenn-Air oven indicates a fault with the main ACU (Appliance Control Unit), specifically a pin short detected on the control board. This is often caused by contamination such as grease or moisture on the surface of the PCB, which creates unintended electrical connections between pins. Components like the door latch board and cavity temperature sensor circuits are commonly involved in this fault.
Will resetting the oven clear the F1E1-A error code?
Unplugging the oven or disconnecting power may temporarily clear the F1E1-A code, but if the underlying cause, such as contamination on the PCB or a loose connector, is not addressed, the fault will return. A power reset is a useful first step for diagnosis but is not a permanent fix. After resetting, inspect all ACU connections and the board surface before restoring power.
Is it safe to use my Jenn-Air oven when F1E1-A is displayed?
You should not continue using the oven while this fault code is active. The F1E1-A code indicates an electrical fault within the main control board, and operating the oven in this state could cause additional damage to control components or create an unsafe condition. Disconnect power and perform diagnostics before resuming use.
How do I fix the F1E1-A error on a Jenn-Air oven?
Start by unplugging the range or disconnecting power at the breaker. Inspect all harness connectors attached to the main ACU for any that are loose, unplugged, or showing signs of corrosion, and reseat them firmly. Visually examine the PCB surface for contamination such as grease or moisture and address any found. If connections are secure and the board appears clean but the code returns, the cavity temperature sensor wiring, door latch board connection, or the ACU itself may need to be replaced.
How much does it cost to repair a Jenn-Air oven showing F1E1-A?
Repair costs vary depending on the root cause. If the fix involves cleaning contamination or reseating connectors, there may be little to no parts cost, though a service call typically runs between $75 and $150. If the cavity temperature sensor wiring or door latch board needs replacement, parts and labor combined generally range from $150 to $350. A failed main ACU control board is the most expensive scenario, with total repair costs typically falling between $300 and $600 or more depending on the specific board and labor rates in your area.

Related Jenn-Air oven codes

All Jenn-Air oven codes
View all 154 Jenn-Air oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass