mypros+
Error code reference

Jenn-Air Oven Error Code F3E9-0

Secondary cavity meat probe temp sensor shorted.

Jenn-Air codesJenn-Air oven codes

Secondary cavity meat probe temp sensor shorted.

First step from the service manual

Enter Diagnostics mode and verify meat probe is at room temperature (50°F to 90°F).

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F3E9-0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F3E9-0 means on a Jenn-Air oven

The F3E9-0 error code indicates that the meat probe temperature sensor in the secondary oven cavity has developed a short circuit condition. In a dual-cavity Jenn-Air oven, each cavity has its own probe input circuit, and this code specifically targets the secondary (lower or second) cavity's probe sensor. A shorted sensor means the resistance in the probe circuit has dropped abnormally low, which the oven's control board interprets as an implausible temperature reading and flags as a fault.

The meat probe is a thermistor-based sensor that changes resistance according to the temperature of the food it is inserted into. Under normal room-temperature conditions (50°F to 90°F), the probe should read within an expected resistance range. When the probe or its wiring shorts, the control board sees a resistance value well below the normal range, triggering F3E9-0. Common sources of a short include damaged probe wiring, a bent or broken probe tip making unintended contact, or internal failure of the probe's thermistor element.

The first diagnostic step is to enter the oven's Diagnostics mode and confirm that no probe is inserted, or that an inserted probe is at room temperature within the 50°F to 90°F window. If the fault persists with no probe connected, the issue may lie in the secondary cavity's probe receptacle or the wiring harness leading to the control board. If the fault clears when the probe is unplugged, the probe itself is the most likely failed component.

Source: manufacturer service documentation.

Common causes of F3E9-0

  1. 01

    Damaged or failed meat probe

    Part replacement

    The probe's internal thermistor element can short internally due to physical damage, exposure to excessive heat, or normal wear over time. Unplugging the probe and checking whether the fault clears will help confirm this.

  2. 02

    Probe cable or connector damage

    Part replacement

    The probe's cord can develop a short if it has been pinched in an oven door, burned against a heating element, or if the connector pins have bent or corroded. Inspect the cable and connector carefully for visible damage.

  3. 03

    Debris or moisture in the probe receptacle

    Wiring / connection

    Food residue, grease, or moisture inside the secondary cavity's probe jack can create an unintended electrical short across the contacts. Inspect and clean the receptacle with the oven powered off.

  4. 04

    Faulty probe receptacle in the secondary cavity

    Part replacement

    The socket that the probe plugs into can fail internally, causing a short circuit even when no probe is inserted. If the fault persists with the probe disconnected, the receptacle itself may need replacement.

  5. 05

    Control board probe input circuit failure

    Part replacement

    If all probe components and wiring check out correctly, the probe input circuit on the main control board may have failed. This is less common but possible if the fault persists after replacing the probe and inspecting the receptacle and wiring.

See the test procedure for each cause

Frequently asked questions about F3E9-0

What does F3E9-0 mean on a Jenn-Air oven?
F3E9-0 means the meat probe temperature sensor in the secondary oven cavity has a short circuit condition. The control board has detected an abnormally low resistance in the probe circuit, which indicates a failed probe, damaged wiring, or a faulty receptacle. The oven flags this fault to prevent incorrect cooking based on a bad temperature reading.
How do I fix the F3E9-0 error on my Jenn-Air oven?
Start by entering Diagnostics mode and verifying that the probe reads within the expected range at room temperature (50°F to 90°F). Unplug the meat probe from the secondary cavity and check whether the error clears. If it does, the probe is likely shorted and should be replaced. If the error persists with no probe connected, inspect the receptacle and wiring harness for damage or contamination.
Is it safe to use my Jenn-Air oven while F3E9-0 is displayed?
If only the secondary cavity is affected and the oven still allows operation in the primary cavity, you can use that function with caution. However, you should not ignore this fault, as a shorted probe circuit can interfere with cooking accuracy. Avoid using the meat probe feature in the secondary cavity until the fault is diagnosed and repaired.
Will resetting my Jenn-Air oven clear the F3E9-0 error code?
A power reset by turning off the circuit breaker for one to two minutes may temporarily clear the fault, but if the underlying short circuit condition remains in the probe, receptacle, or wiring, the code will return. A reset alone is not a fix and should only be used as part of diagnosing whether the fault is intermittent or persistent.
How much does it cost to repair the F3E9-0 error on a Jenn-Air oven?
If the meat probe itself is the cause, replacement probes typically cost in the range of $30 to $80 depending on the model. A probe receptacle replacement, including parts and labor, generally runs between $100 and $200. If the main control board needs replacement, costs can range from $200 to $450 or more for parts and professional labor.

Related Jenn-Air oven codes

All Jenn-Air oven codes
View all 154 Jenn-Air oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass