mypros+
Error code reference

Maytag Oven Error Code 1d12

Runaway temperature (650°F) detected with door unlocked (lower oven); sensor resistance > 2237 ohms.

Maytag codesMaytag oven codes

Runaway temperature (650°F) detected with door unlocked (lower oven); sensor resistance > 2237 ohms.

First step from the service manual

Check temperature sensor and oven relay operation; control disables all cook functions for cavity.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 1d12.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 1d12 means on a Maytag oven

Error code 1d12 on a Maytag oven indicates the control board has detected a runaway temperature condition in the lower oven, with the oven door in the unlocked position. Specifically, the oven temperature reached or exceeded 650°F during a standard cooking cycle, which is outside the acceptable operating range. The control board cross-references temperature data from the lower oven sensor and, when the reading surpasses this threshold without a corresponding self-clean cycle being active, triggers the 1d12 fault and shuts down the heating circuit. Sensor resistance above 2237 ohms at room temperature points directly to a failed or degraded oven temperature sensor as the primary suspect.

For homeowners, this code means your lower oven's temperature sensor is likely sending incorrect readings to the control board, causing the oven to think temperatures are dangerously high, even if the oven feels normal. The sensor is a small probe mounted inside the oven cavity, and when it fails, it can report false high temperatures. The oven locks out to prevent a genuine overheating event. This is a protective measure, not a minor glitch, and the oven should not be used until the cause is identified and resolved.

Before replacing any parts, measure the resistance of the lower oven sensor at the control board connector using a multimeter. A healthy sensor reads approximately 1080 ohms at 70°F. A reading above 2237 ohms confirms sensor failure and replacement is required.

Source: manufacturer service documentation.

Common causes of 1d12

  1. 01

    Failed lower oven temperature sensor

    Part replacement

    The lower oven temperature sensor has drifted out of spec or failed open, producing resistance above 2237 ohms instead of the expected ~1080 ohms at 70°F. This causes the control board to interpret falsely high temperatures and trigger the 1d12 runaway condition.

  2. 02

    Damaged or shorted sensor wiring harness

    Part replacement

    The wiring harness connecting the lower oven sensor to the control board may have cracked insulation, a pinched wire, or a loose connector, causing incorrect resistance readings at the board even when the sensor itself is within spec. Heat cycling over time is a common cause of harness degradation in oven cavities.

  3. 03

    Actual lower oven overheating due to failed temperature limiter or relay

    Part replacement

    If the oven is genuinely reaching temperatures near or above 650°F, a stuck relay on the control board or a failed high-limit thermostat may be allowing the heating element to run without regulation. In this scenario, the sensor is correctly reporting a real overheat condition rather than a false one.

  4. 04

    Faulty electronic control board

    Part replacement

    If the lower oven sensor and its wiring harness both test within spec, the control board itself may be misreading the sensor signal due to a failed input circuit. This is the least common cause and should only be considered after the sensor and wiring are confirmed good.

See the test procedure for each cause

Frequently asked questions about 1d12

What does error code 1d12 mean on a Maytag oven?
Error code 1d12 means the control board detected a runaway temperature of 650°F or higher in the lower oven while the door was unlocked. This triggers a protective lockout to prevent a genuine overheating event. The most common cause is a failed lower oven temperature sensor reading above 2237 ohms, which causes the board to see a falsely high temperature and shut the oven down.
Is it safe to use my Maytag oven when error code 1d12 is showing?
No, you should not use the lower oven while 1d12 is active. The code indicates either a real overheating condition or a sensor failure that prevents the control board from accurately monitoring oven temperature. In either case, operating the oven without a functioning temperature sensor removes the safety controls designed to prevent damage or fire. Diagnose and resolve the fault before resuming use.
How do I fix error code 1d12 on a Maytag oven?
Start by testing the lower oven temperature sensor resistance with a multimeter at room temperature (approximately 70°F). The sensor should read around 1080 ohms; a reading above 2237 ohms means the sensor has failed and needs to be replaced. If the sensor tests good, inspect the wiring harness between the sensor and the control board for damage, burns, or loose connections. If both test good, the control board may be at fault, and professional diagnosis is advisable at that point.
How much does it cost to fix a 1d12 error on a Maytag oven?
A replacement lower oven temperature sensor typically costs between $20 and $60 for the part, and replacing it is a manageable DIY repair requiring only a screwdriver and a multimeter. If the control board is the cause, board replacements range from $150 to $350 or more for the part alone, and professional labor adds $100 to $200 depending on your area. Confirming the sensor is the problem with a resistance test before ordering parts will save unnecessary expense.
Can I reset a Maytag oven 1d12 error by unplugging it?
Unplugging the oven or cutting power at the breaker for 30 seconds will clear the 1d12 code temporarily, and the oven may operate again until the fault condition is detected again. However, if the underlying sensor failure or wiring issue is not corrected, the code will return, often quickly. Clearing the code without fixing the root cause is not a repair and does not make the oven safe to use long-term.

Related Maytag oven codes

All Maytag oven codes
View all 103 Maytag oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass