mypros+
Error code reference

Maytag Washer Error Code d19/F29

Door unlock error-door is unable to unlock after 6 tries.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the d19/F29 error code actually means

Your Maytag washer tried to unlock the door six times and failed, so it stopped and displayed this error to protect your laundry and the machine. The door lock mechanism is not releasing the way it should, which could be due to a worn latch part or a wiring issue. You will need to manually release the door before you can access the laundry or begin troubleshooting.

Diagnostic procedure

The full d19/F29 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Clear error code, unplug washer, manually unlock the door (page 15).
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock d19/F29 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of d19/F29

Ranked by how often they cause this code
  1. 1Failed Door Latch Assembly
  2. 2Wiring Harness Damage or Loose Connector
  3. 3Door Latch Mechanical Obstruction
  4. 4Control Board Fault
  5. 5Door Strike or Hinge Misalignment

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about d19/F29

What does d19/F29 mean on a Maytag washer?
The d19/F29 code means the washer's control board attempted to unlock the door six times and was unable to confirm a successful unlock. This fault is specific to the door latch system and causes the machine to stop operation until the issue is resolved. The door will need to be manually released before laundry can be retrieved or repairs can begin.
Is it safe to use my Maytag washer when the d19/F29 error is showing?
You should not continue running the washer while this error is active. The machine has already shut itself down as a protective measure because it cannot confirm the door will unlock properly. Attempting to run cycles with a malfunctioning door latch could trap laundry inside or lead to further component damage.
How much does it cost to repair a Maytag washer with a d19/F29 error?
Repair costs depend on the root cause. A replacement door latch assembly typically costs between $30 and $80 for the part alone. If a control board replacement is required, parts can range from $100 to $250 or more. Adding professional labor, total repair costs generally fall between $100 and $350 depending on the failed component and your location.
How do I fix the d19/F29 error on my Maytag washer?
Start by clearing the error code, then unplug the washer and use the manual door release procedure to open the door safely. Once the door is open, inspect the door latch assembly and the wiring harness connecting it to the control board. If the latch actuator has failed mechanically or electrically, replacing the door latch assembly is typically the repair needed.
Will resetting my Maytag washer clear the d19/F29 error?
Clearing the error code may temporarily remove the fault display, but if the underlying cause is not corrected, the code will return the next time the washer attempts to unlock the door after a cycle. A reset is a useful first step for diagnosis, but it is not a fix for a failed latch, wiring problem, or control board issue.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass