mypros+
Model reference

Caloric DCR-225-1V-OK

Dishwasher

4 documents91 error codes35 service modes

Available documentation

Tech Sheet

  • Tech sheet44 pg
    Covers this model
  • Whirlpool Commercial Stack Washer Dryer CGT8000XQ1 W10394865 Tech Sheet40 pg
    Covers this model
  • Tech Sheet - W11696819 - Rev A48 pg
    Covers this model
  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR-225-1V-OK.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (91)

CodeMeaning
d 13Coin 2 errord 16Generation 2 debit card reader errord10/F31Overheating of motord11/F11Washer MCU errord12/F25Tachometer errord13Coin 2 sensor detected as blocked for 8 seconds, or coin drop UI control…d14/F33Pump disconnectedd15/F34Load detected in washer during Washer Cleanout Cycle.d16Generation 2 debit card reader errord17/F22Door lock errord19/F29Door unlock errord2/F22Dryer exhaust thermistor open errord20/F28Communication failure between CCU and MCU.d21/F27Overflow conditiond22/F70Communication failure from CCU to UICd23/F70Washer communication failure between CCU and UIC.d23/F71Communication failure from UIC to CCUd24/F24Temperature sensor errord3/F23Dryer exhaust thermistor shorted errord3/F73Washer UIC failured3/F74Washer UIC failured4/F01Dryer motor control circuit errord4/F26Door switch errord5Coin 1 sensor detected as blocked for 8 seconds, or coin drop UI control…d6Coin 2 error (dryer)d6/F01Washer CCU errord7/F20No water detected entering washerd8/F21Long draind8/F73UIC Microprocessor errord8/F74UIC EEPROM error
View all 91 error codes
d9Low voltage detection errorF 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnectedF 34Load detected in washer during Washer Cleanout Cycle.F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorf01Dryer motor control circuit error; the control cannot determine if the motor…F03Washer accelerometer failure; X, Y, and Z limits are outside normal range…F03/F04Accelerometer failureF04Washer accelerometer failureF11MCU (Motor Control Unit) error/failure, possibly caused by a repeating under or…F1E1Indicates a CCU (Cycle Control Unit) problem.F20No water detected entering washerF21Long drainf22Dryer exhaust thermistor open errorf23Dryer exhaust thermistor shorted errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between washer CCU and MCU.F29Door unlock errorF2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms).F3E4Inlet thermistor is shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; only appears in service diagnostic mode.F3E7Moisture sensor strip has shorted; only appears in service diagnostic mode.F4E1No voltage detected at the heater relay; appears only in Diagnostic Test Mode.F4E3Restricted/low air flow that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F6E1Communication error from UI to CCU; communication between CCU and UI has not…F6E2Communication error from CCU to UI; communication between CCU and UI has not…f70Communication failure from dryer CCU to UIC; UIC is not receiving…f71Communication failure from UIC to dryer CCU; CCU is not receiving…f73UIC Microprocessor errorF73/F74Washer UIC failuref74UIC EEPROM errorLLow L2 voltage (less than 50V) detected at the CCU; displayed on models 4000…L2Low L2 voltage (less than 50V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (35)

  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • Diagnostic Mode["First enter 'Start Operating Set-Up' (Set-Up Mode).","Press and hold the lower right (COLD)…
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • Dryer Field Diagnostic Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM
  • Help Mode["Press the lower left (HOT) button while in special pricing option 2.XX (or while dAS displays if…
  • Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
  • Help Mode (PD Models)["Open the service door.","Press EXTRA RINSE washer keypad until display reads 2.XX.","Press…
  • Install Diagnostics["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
  • P-01 Cancel Cycle, Reset Errors, and Clear Escrow["Enter Service Diagnostic Test Mode.","Display shows P-01.","Press START to clear an active error…
  • P-02 Cycle Credit["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-02 is displayed.","Press START to…
  • P-03 Quick Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-03 is displayed.","Press START to…
  • P-04 Manual Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-04 is displayed.","Press START to…
  • P-05 Button Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-05 is displayed.","Press START to…
  • P-06 Drain and Spin["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-06 is displayed.","Press START to…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-07 is displayed.","Press START to…
  • P-08 Clean Washer Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-08 is displayed.","Press START to…
  • P-10 Dryer Diagnostic Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until P-10 is displayed.","Press START to…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Diagnostic Test Mode["Enter service mode per Control Set-Up Procedures (insert service switch key and turn…
  • Set-up Mode["PD/PR Models
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Setup Mode["PD/PR Models
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Washer Cleanout Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cleanout Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (BRIGHTS) button."]
  • Washer Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Cycle Credit (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (PERM
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Manual Overview Test Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Overview Test Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (DELICATES AND KNITS)…
  • Washer Quick Spin Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]
  • Washer Quick Spin Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (COLORS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax