mypros+
Model reference

Caloric DCR211-1C-OS

Dishwasher

1 document40 error codes8 service modes

Available documentation

Wiring Diagram

  • Wiring Sheet - W11335900 - Rev A2 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR211-1C-OS.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (40)

CodeMeaning
AFLow airflow detected that may affect dryer performance.F0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E4High temperature error during wash cycle.F0E5Off balance load detected.F12E0Communication between the Human Machine Interface and Wi-Fi Module has not been…F1E1Motor relay stuck on, indicates an ACU problem.F1E2MCU over- or under-voltage error.F1E3Incorrect controller installed (electric models only); ACU or UI part number…F1E5ACU parameter file missing; parameter memory invalid.F2E1Stuck button on User Interface (depressed for over 20 seconds); only appears in…F2E4UI software errorF2E5UI software errorF3E1Exhaust thermistor open or shorted; open if temperature drops below 18°F (>50k…F3E2Moisture sensor strip is open or shorted; only appears in service diagnostic…F3E3Inlet thermistor open or shorted; open if temperature drops below 18°F (>245k…F3E6Accelerometer error.F4E1Heater 1 failure or connector problem; no voltage detected at the heater relay.F4E2Heating timeout.F4E3Restricted airflow; low airflow that may affect dryer performance.F4E4L2 line voltage error (electric models only); low L2 voltage (less than 50V)…F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6E1No communication from the HMI detected by ACU.F6E2Communication errorF6E3Communication errorF7E10Motor disconnected error.F7E12MC/MCU overload.F7E2MC/MCU over temperature error or over current error/internal failure.
View all 40 error codes
F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate display F7E10).F7ECMC/MCU overload (alternate display F7E12).F8E1Water inlet valve failure.F8E3Overflow condition detected.F9E1Long drain time.FCE0Communication between the Human Machine Interface and Wi-Fi Module has not been…L2Low L2 voltage (less than 30V) detected at the CCU.PFPower failure occurred while the dryer was running.

Service modes (8)

  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS or DRY LEVEL…
  • Fault/Error Code DisplayEnter Service Diagnostic Mode; the most recent fault code is shown automatically upon entry
  • Human-Machine Interface TestFrom within Service Diagnostic Mode, press and release the 1st button used to activate Service…
  • Key Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Quick Diagnostic TestFrom within Service Diagnostic Mode, press and release the 2nd button used to activate Service…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Test Mode["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax