mypros+
Model reference

Caloric DCS-211-1L

Dishwasher

1 document56 error codes17 service modes

Available documentation

Tech Sheet

  • Basic Operation of Commercial Stacked Washer/dryer20 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCS-211-1L.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (56)

CodeMeaning
d 13Coin 2 errord 16Generation 2 debit card reader errord13Washer Coin 2 errord16Generation 2 debit card reader errord5Washer Coin 1 errord9Washer low voltage detection errorE2Overheating of the induction coil (display flashing).E5Error on filter board due to incorrect wiring or error on power board.E6Error on power unit due to incorrect wiring or error on power board.E9Coil temperature sensor defective.Er 20Flash failure; microcontroller (μC) is faulty.Er 22Permanent use of keypads; control unit cuts off after 10 seconds due to water…Er 31Configuration data incorrect; configuration of induction necessary.Er 36NTC value is not within its specification (value < 200 mV or > 4.9 V); control…Er 47Communication error between touch control (TC) and induction module; none or…F 01Dryer motor control circuit errorF 04Accelerometer failureF 11MCU errorF 20No water detected entering washerF 21Long drainF 22Door lock errorF 23Dryer exhaust thermistor shorted errorF 24Temperature sensor errorF 25Tachometer errorF 26Door switch errorF 27Overflow conditionsF 28Communication failure between CCU and MCU.F 29Door unlock errorF 31Overheating of motorF 33Pump disconnected
View all 56 error codes
F 34Load detected in washer during Washer Cleanout Cycle.F 70Communication failure between CCU and UIC.F 71Dryer communication failure from UIC to dryer CCUF 73UIC failure (washer) / UIC Microprocessor error (dryer)F 74UIC EEPROM errorF01Washer CCU errorF04Washer accelerometer failureF11Washer MCU errorF20Washer no water detected entering washerF21Washer long drainF22Washer door lock errorF23Dryer exhaust thermistor shorted errorF24Washer temperature sensor errorF25Washer tachometer errorF26Washer door switch errorF27Washer overflow conditionF28Washer communication failure between CCU and MCU.F29Washer door unlock errorF31Washer motor overheatingF33Washer pump disconnectedF34Washer load detected during Washer Cleanout Cycle.F70Washer communication failure between CCU and UIC.F71Dryer communication failure from UIC to dryer CCUF73Dryer UIC microprocessor errorF74Washer UIC EEPROM error.U400Secondary voltage of the power unit too high (primary > 300 V); control unit…

Service modes (17)

  • Diagnostic Mode["First enter Set-Up Mode (Start Operating Set-Up).","Press and hold the lower right (COLD) button…
  • Diagnostic Test Mode1
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS)…
  • Dryer Field Diagnostic Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM PRESS) button."]
  • Help Mode["Press the lower left (HOT) button while in special pricing option 2.XX (or while dAS displays if…
  • Set-Up Mode["Coin Payment Models
  • Set-Up Mode (Coin Payment)["Insert service switch key and turn counter-clockwise."]
  • Washer Cleanout Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cleanout Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (COLORS/DELICATES)…
  • Washer Cycle Credit["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Cycle Credit (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (HOT) button (CC will…
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Manual Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (COTTON/WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Overview Test Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (WARM) button."]
  • Washer Quick Spin Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]
  • Washer Quick Spin Cycle (Diagnostic Sub-Mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (PERM PRESS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax