mypros+
Model reference

Caloric DCS-415-1D

Dishwasher

3 documents45 error codes17 service modes

Available documentation

Tech Sheet

  • techsheet-w10254504-reva56 pg
    Covers this model
  • Tech Sheet - W10254472 - Rev A48 pg
    Covers this model
  • Tech Sheet - W10441081 - Rev C_W1044108144 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCS-415-1D.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (45)

CodeMeaning
1c1cShorted key detected on control circuit board.1c31Cancel key circuit problem1c4cMicro communication failure1c5cVcc or ground fault detected at test point during cook active.1c6cEEPROM error detected during cook active.1c7cControl not calibrated1c8cCooking program error detected during cook active.1d11Runaway oven temperature3d11Oven temperature sensor open circuit detected during cook active.3d21Oven temperature sensor shorted detected during cook active.F0E1Load detected during the washer cleaning cycle; a load was detected inside the…F1E1CCU errorF1E2MCU errorF2E2User Interface (UI) software errorF2E3Unsupported cycleF3E1Pressure sensor errorF3E2Temperature sensor errorF3E4Level or presence sensor errorF4E0Heater is not detectedF5E1Door switch errorF5E2Door lock errorF5E3Door unlock errorF6E1Communication error between CCU and MCUF6E2Communication error between CCU and UIF6E3Communication error between CCU and UIF6E5Communication error between CCU and Expansion BoardF7E1Drive motor speed sensing error / washer overloadF7E2MCU overheat and/or motor overheatF8E0Steam inlet valve errorF8E1No water detected entering washer or pressure switch trip not detected
View all 45 error codes
F8E2Dispenser system errorF8E3Overflow conditionF8E4Flow meter faultF9E1Long drainFCE0Communication error, ECM to CCU (model WFL98 only).FCE1Communication error, washer to wireless router (model WFL98 only).FCE2Wireless router cannot communicate with the internet (model WFL98 only).FCE3Antenna A (J2) bad (model WFL98 only).FCE4Antenna B (J11) bad (model WFL98 only).FCE5Current transformer A not functioning (J12) (model WFL98 only).FCE7Provisioning failurerLLoad detected during the washer cleaning cycle (remove load); saved as F0E1.SdSuds detected (alternate display)SudSuds detectedSUDSSuds detected

Service modes (17)

  • Clear Fault Codes1
  • Component ActivationFrom the Diagnostic Home screen, select 'Component Activation'
  • Diagnostic Code Display["Press and hold the Up Arrow pad for 3 to 5 seconds when applying power to the unit.","The last 5…
  • Fault Code Display1
  • Fault/Error Code Display["Activate Service Diagnostic Mode first.","Press and release the 3rd button used to activate…
  • Keypad Lockout["Press and hold Cancel and Timer pads for 3 to 5 seconds.","Press Up or Down Arrow pads to…
  • One-Watt Standby Mode["Press and hold Cancel and Down Arrow pads for 3 to 5 seconds."]
  • Oven Temperature Adjustment["Press Bake pad.","Enter 550 on the digit-pad (press Up Arrow pad).","Immediately press and hold…
  • Quick Diagnostic TestFrom the Diagnostics Home Screen, navigate to Error Diagnostic, then select Quick Diagnostic Test
  • Quick Diagnostics1
  • Quick Test Mode (Non-Self Clean Control)["Apply power to the range.","Within 5 minutes of applying power, press and hold Cancel and Broil…
  • Sabbath Mode["Initiate desired bake function first.","Press and hold Clock pad for 3 to 5 seconds to…
  • Service Diagnostic Mode1. Ensure washer is in standby mode (plugged in with all indicators off). 2. Select any three (3)…
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • Temperature Display (°F/°C)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press Up or Down Arrow pads to change…
  • UI Component TestFrom Diagnostics Home Screen, navigate to Component Activation, then select UI Component Test
  • User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax