mypros+
Model reference

Caloric DCS215-1H-OA

Dishwasher

9 documents92 error codes28 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W10195615 - Rev B2 pg
    Covers this model
  • Kitchnaid Dishwasher KUDC10FXSS0 KUDC10FXSS1 KUDC10FXSS2 KUDC10FXSS3 Tech Sheet2 pg
    Covers this model
  • Kitchenaid Dishwasher KUDS30IXWH4 Tech Sheet2 pg
    Covers this model
  • Tech Sheet - W10350140 - Rev B2 pg
    Covers this model
  • Whirlpool Dishwasher WDT910SAYM0 Tech Sheet2 pg
    Covers this model
  • Tech Sheet - W103503332 pg
    Covers this model
  • Whirlpool Dishwasher WDF530PLYW0 Tech Sheet2 pg
    Covers this model

Service Manual

  • SERVICE MANUAL - Maytag Dishwashers 4-Blade Stainless Steel Chopper76 pg
    Covers this model

Other

  • W10195613 - Rev D_W101956132 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCS215-1H-OA.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (92)

CodeMeaning
:Flashing colon indicates a power failure has occurred.1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board or incompatible software…1-3Control detected stuck key(s) in keypad or keypad connection.10-1Dispenser electrical problem10-2Vent wax motor electrical problem.10-3Drying fan error2-1User interface stuck key or short circuit(s) in keypad or in control's input…2-2Software or hardware incompatibility problem with control (User Interface).3-1Open temperature sensing circuit3-2Shorted temperature sensing circuit3-3OWI/thermistor sensor failed calibration.4-1No communication between control and wash motor.4-2Motor communication error between control and wash motor.4-3Wash motor not running5-1Door stuck open5-2Door stuck closed6-1Inlet water6-2Inlet water6-3Inlet water6-4Inlet water6-6Inlet water6-7Disconnected or damaged flowmeter.6-8Inlet water7-1Heating7-2Heating7-7Flowmeter problem8-1Draining8-2Draining8-3Draining
View all 92 error codes
8-3 (stuck on)Drain stuck on9-1Diverter9-2Diverter stuck on9-3Diverter disk missing from sump.dLDoor lock failuredUDoor unlock failureF1Pressure signal out-of-rangeF1-E1Control detected K2 pilot relay stuck closed.F1-E2Control software issueF10-E1Dispenser electrical problemF10-E3Drying fan errorF2Keypad/User interface failureF2-E1Control detected stuck key(s) in keypad or keypad connection.F3-E1Open connection or component in temperature sensing circuit; open or faulty…F3-E2Shorted connection or component in temperature sensing circuit; incoming water…F3-E3OWI failed calibration.F30Long fill (saved code for LF).F32Long drain (saved code for Ld).F3HHumidity sensor failure.F4-E3Wash motor not runningF40ATC thermistor open/shortF41Motor RPS thermistor open/shortF42Heater thermistor open/short (not used on these models).F5-E1Door stuck openF5-E2Door stuck closedF50Motor stalledF51Motor RPS failureF52Motor stop failureF53Motor control overtempF54Motor control overcurrentF6MW relay (Relay 4903) failure.F6-E1Low/no water (mechanical problem)F6-E2Fill valve electrical problemF6-E3Suds/air in pumpF6-E4Float switch openF6-E7Flowmeter disconnected or damaged.F6-E8Water softener regen valve electrical problemF60Saved fault code for Primary Control Failure.F68Pressure signal out-of-range (saved code for F1).F7-E1No heatF7-E2Heater stuck onF70Overloaded (saved code for oL)F71Suds detection (saved code for Sd)F72Basket re-engagement failureF8-E1Slow drainF8-E2Drain motor electrical problemF8-E3Drain stuck onF80Door lock failure (saved code for dL).F81Open/close door lid (saved code for lid).F82Door lock failure (saved code variant for dL).F83Door unlock failure (saved code for dU).F84Door lock failure (saved code variant for dL).F85Door lock failure (saved code variant for dL).F9-E1Disconnected or damaged flowmeter.HCHot and cold inlet hoses are reversed.LdLong drainLFLong filllidLid openedoLOverloadedPoPump outSdSuds detecteduLUnbalanced load detected

Service modes (28)

  • Automatic Diagnostic Test1
  • Automatic Diagnostic Test Mode["Ensure washer is in standby mode (plugged in with all indicators off, or with only the Clean…
  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval 20, press Hi Temp key when Hi Temp LED is on during the…
  • Clear Error HistoryDuring Service Diagnostics Cycle interval with Hi Temp LED on (10 seconds pause after Error 4)…
  • Console and Indicators Diagnostic Test1. Plug in washer or reconnect power. 2. From Standby (Off) mode, press and release the following…
  • Console and Indicators Diagnostic Test Mode["Plug in washer or reconnect power.","From Standby (Off) Mode, press and release SOIL LEVEL, then…
  • Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
  • Error Code ReadingRun Service Diagnostics Cycle
  • Error Code Reading (during Service Diagnostics)After entering Service Diagnostics Cycle
  • Error Code Reading (within Service Diagnostics)After entering Service Diagnostics Cycle, interval 25 is display test (all LEDs on). Intervals…
  • Error History ReadingEnter Service Diagnostics Cycle. Error codes are displayed in intervals 24 (Error 1
  • Manual Diagnostic Test1
  • Manual Diagnostic Test Mode["Perform steps 1 and 2 of the Automatic Diagnostic Test Mode entry procedure.","During the…
  • Pressure Transducer Calibration["Unplug washer or disconnect power.","Access the machine/motor control assembly.","Check hose…
  • Rapid Advance (Customer Cycle)["Start a customer cycle.","Press HIGH TEMP
  • Rapid Advance (during Service Diagnostics)Press the Start/Resume key to advance 1 interval at a time during the Service Diagnostics Cycle.
  • Rapid Advance ModePress HI TEMP
  • Rapid Advance Mode (Cycle Operation)After starting a cycle, press HI TEMP
  • Rapid Advance Mode (during active cycle)Press HI TEMP
  • Rapid Advance Mode (during customer cycle)Press HI TEMP
  • Rapid Advance Mode (during normal cycle)Press HI TEMP
  • Rapid Advance Mode (in-cycle)After starting a cycle, press HI TEMP
  • Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
  • Service Diagnostic Cycle["Press START/RESUME to wake up the control panel.","Press any 3 keys in the sequence…
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Service Diagnostics Error History ReadoutAfter entering Service Diagnostics Cycle, errors are displayed in intervals 24 (Error 1
  • Service Diagnostics Rapid AdvanceDuring the Service Diagnostics Cycle, press Start/Resume key to advance 1 interval at a time.
  • Touch Panel and PCBA Self-Diagnostic Test Mode["1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax