mypros+
Model reference

Caloric DCR211-1F-OS

Dishwasher

7 documents52 error codes12 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11642952 - Rev A2 pg
    Covers this model
  • Tech Sheet - W10838719 - Rev A12 pg
    Covers this model
  • Tech Sheet W1061005912 pg
    Covers this model
  • MDB4949SDH Tech Sheet W10610054 Rev B12 pg
    Covers this model
  • KDTE104ESS3 Tech Sheet12 pg
    Covers this model
  • Tech Sheet12 pg
    Covers this model
  • Whirlpool Dishwasher WDF760SADM0 Tech Sheet W1061005912 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR211-1F-OS.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (52)

CodeMeaning
:Flashing colon indicates a power failure has occurred.1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in temperature sensing circuit (open or faulty…3-2Shorted connection or component in temperature sensing circuit, shorted or…3-3OWI calibration failure due to OWI sensor failure or drain hose check valve not…4-3Wash motor not running due to loose connection in motor circuit, faulty wash…5-1Door stuck open5-2Door stuck closed6-1Low or no water6-2Fill valve electrical problem6-3Suds or air in pump causing repeated wash periods.6-4Float switch open6-6Incoming water cool6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem7-1No heat7-1 (flowmeter)Disconnected or damaged flowmeter.7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain motor stuck on8-5Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk in sump is missing.
View all 52 error codes
9-4Lower spray arm errorf1 e1Primary control failure.F1E0Internal board failure.F1E1Internal board failure.F1E2A/D error(s).F2Touch panel failure.f2 e1Stuck button or user interface mismatch (only appears in service diagnostic…F2E1Shorted keypad.f3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is open (only appears in service diagnostic mode).f3 e7Moisture sensor strip has shorted (only appears in service diagnostic mode).F3E0Oven sensor opened, oven sensor shorted, bake/broil range over temperature, or…F3HHumidity sensor failure.f4 e4Low line voltage detected.F5E0Door and switches do not agree (Clean mode).F5E1Door latch not operating (Clean mode).F6MW relay failure (Relay 4903 contact may have welded closed).F6E1Oven over temperature when heating.F9E0Miswired house or miswired range.No DisplayControl not operational.pfPower failure occurred while the dryer was running.

Service modes (12)

  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Customer Cycle Rapid Advance["Start a customer cycle.","Press HIGH TEMP
  • Customer-Focused Drying Mode Adjustment1
  • Diagnostics ModePress CANCEL > CANCEL > START within 5 seconds.
  • Rapid Advance (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Self-diagnostic / Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Service Diagnostic Mode1
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Touch Panel and Electronic Control Self-Diagnostic Test Mode["Press and hold the CANCEL/OFF button while opening the door.","While still holding the CANCEL/OFF…
  • User Interface/Control System TestFrom within Service Diagnostic Mode, press and release the 1st button used to activate Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax