mypros+
Model reference

Caloric DCR225-1D-OS

Dishwasher

6 documents85 error codes19 service modes

Available documentation

Tech Sheet

  • Tech Sheet2 pg
    Covers this model
  • techsheet-w10254504-reva56 pg
    Covers this model
  • Tech Sheet - W11720123 - Rev A2 pg
    Covers this model
  • Tech Sheet - W10254472 - Rev A48 pg
    Covers this model
  • Tech Sheet - W11639170 - Rev A2 pg
    Covers this model
  • Tech Sheet - W10441081 - Rev C_W1044108144 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR225-1D-OS.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (85)

CodeMeaning
doorDoor switch circuit is opendSFLFault detected in the microprocessor temperature sensing circuitF0E1Load detected during the washer cleaning cycle; a load was detected inside the…f1 e1Primary control failure.F1 E4HMI (Human Machine Interface) Fault.F1 E6Voltage Input Fault.F11E1Main cavity over temperature condition.F12E1Model/Serial number not programmed.F12E2Model/Serial number do not match.F12E3Wi-Fi radio fault.F14E7Main cavity broil element fault.F14E8Main cavity convection element fault.F1E1Primary control failure.F1E2MCU errorf2 e1Stuck button or user interface mismatch (only appears in service diagnostic…F2E1Stuck button or user interface mismatch (keypad/user interface failure)F2E2User Interface (UI) software errorF2E3Unsupported cycleF2E4HMI 1 (Human Machine Interface 1) fault.F2E5HMI 1 fault.f3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is open (only appears in service diagnostic mode).f3 e7Moisture sensor strip has shorted (only appears in service diagnostic mode).F3E0Main oven temperature sensor fault.F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E4Level or presence sensor errorF3E6Moisture sensor strip is openF3E7Moisture sensor strip has shorted
View all 85 error codes
f4 e4Low line voltage detected.F4E0Heater is not detectedF5 E1Dryer Door Circuit Error.F5E0Main door and latch switches do not agree.F5E1Door switch errorF5E2Door lock errorF5E3Door unlock errorF6 E1ACU to HMI Communication FaultF6E1Communication error between CCU and MCUF6E2Communication error between CCU and UIF6E3Communication error between CCU and UIF6E5Communication error between CCU and Expansion BoardF7 E6Dryer Motor Circuit Error.F7 E8Dryer Motor Sense Error.F7E1Drive motor speed sensing error / washer overloadF7E2MCU overheat and/or motor overheatF7E5Cooling fan error.F7E6Cooling fan blocked.f8 e1No voltage detected at the water valve relay (steam models only)F8E0Steam inlet valve errorF8E1No voltage detected at the water valve relay (steam models only)F8E2Dispenser system errorF8E3Overflow conditionF8E4Flow meter faultF9E0Power cord miswired.F9E1Long drainFBE1Main cavity over temperature condition.FC E1Model/Serial not programmed.FC E2Model and Serial do not match.FC E4USB FaultFC E5Software Update FailureFC E6Model Setup Export FailureFC E7Model Setup Import FailureFCE0Communication error, ECM to CCU (model WFL98 only).FCE1Model/Serial number not programmed into the control.FCE2Model/Serial number do not match between components.FCE3Wi-Fi radio fault.FCE4Antenna B (J11) bad (model WFL98 only).FCE5Current transformer A not functioning (J12) (model WFL98 only).FCE7Provisioning failureFEE6Main cavity bake element fault.FEE7Main cavity broil element fault.FEE8No description availableFILLNormal idle/ready state display indicating the dryer is ready to accept a cycle…FP E1Coin 1 Circuit Error.FP E2Coin 2 Circuit Error.FP E3Card Reader Communication error.HotPossible overheating conditionpfPower failure occurred while the dryer was running.rLLoad detected during the washer cleaning cycle (remove load); saved as F0E1.SdSuds detected (alternate display)SEFLRotational sensor circuit failureSudSuds detectedSUDSSuds detectedU1Communication or control board fault (unspecified U1 error).

Service modes (19)

  • Clear Fault Codes1
  • Component ActivationFrom the Diagnostic Home screen, select 'Component Activation'
  • Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode.","Press and hold the TEMP button for more than 6…
  • Diagnostic ModePress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
  • Fault Code Display1
  • Fault/Error Code Display["Activate Service Diagnostic Mode first.","Press and release the 3rd button used to activate…
  • Help ModePress the HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
  • Model/Serial Number MenuEnter Help Mode, then while on the S0 screen press the HEAVY DUTY keypad
  • Quick Diagnostic TestFrom the Diagnostics Home Screen, navigate to Error Diagnostic, then select Quick Diagnostic Test
  • Quick Diagnostics1
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only DONE or…
  • Service Diagnostics Mode - Option A["Press Settings > Diagnostics home > Service Diagnostics Code.","Enter code 111 111 111 (Digit 1…
  • Service Diagnostics Mode - Option B["Press Settings > Diagnostics home > Service Diagnostics Code.","Enter any 3 digits and repeat the…
  • Set-Up ModePD Models
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • UI Component TestFrom Diagnostics Home Screen, navigate to Component Activation, then select UI Component Test
  • USB MenuEnter Help Mode, then while on the USB screen press the HEAVY DUTY keypad
  • User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • User Interface/Control System Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax