mypros+
Model reference

Caloric DCR-225-1W-OM

Dishwasher

1 document64 error codes20 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W1058050912 pg
    Covers this model
MyPros+ Max

Diagnose your Caloric DCR-225-1W-OM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (64)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Control software issue10-1Dispenser electrical problem10-3Drying fan error2-1Stuck key detected in keypad or keypad connection.3-1Thermistor/OWI temperature sensor circuit open3-2Thermistor/OWI temperature sensor circuit shorted3-3OWI failed calibration4-3Wash motor not running5-1Door switch stuck open5-2Door switch stuck closed6-1Low/no water6-2Fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Cool water6-7Flowmeter error6-8Water softener regeneration valve electrical problem7-1No heat7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain stuck ond13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF0 E7Low Voltage ErrorF01MCC (Central Control Module) communication errorF03Accelerometer failure
View all 64 error codes
F04Accelerometer failureF1 E1ACU FaultF1 E7ACU Voltage Input FaultF11Motor Control Module (MCM) failureF2 E1Lower Dryer Keypad Stuck ErrorF2 E2Upper Dryer Keypad Stuck ErrorF20No water entry detectedF21Excessive drain timeF22Door lock errorF24Water temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between MCC and MCM.F29Motor overheating detected.F30No description availableF31No description availableF33Pump disconnectedF34Load detected in the washer during the washer cleaning cycle.F5 E1Lower Dryer Door Circuit ErrorF5 E6Upper Dryer Door Circuit ErrorF7 E6Lower Dryer Motor Circuit ErrorF7 E7Upper Dryer Motor Circuit ErrorF7 E8Lower Dryer Motor Sense ErrorF7 E9Upper Dryer Motor Sense ErrorF70Communication failure between MCC and User Interface (UI).F73User Interface (UI) failureF74User Interface (UI) failureFC E1Model/Serial not ProgrammedFC E4USB FaultFC E5Software Update FailureFP E1Coin 1 Circuit ErrorFP E2Coin 2 Circuit ErrorFP E3Card Reader Communication Error

Service modes (20)

  • Diagnostic Mode (Blink Mode)["First access Setup/Configuration Mode.","Press DELICATES & KNITS button for 1 second while one of…
  • Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • Help Mode["PD models
  • Help Mode (dAS mode)1
  • Help Mode (PD models)1
  • Manual Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WHITES button while the display is blinking."]
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Quick Drain and Spin["Enter Diagnostic Mode (Blink Mode).","Press COLORS button while the display is blinking."]
  • Quick Overview Test["Enter Diagnostic Mode (Blink Mode).","Press WOOLENS button while the display is blinking."]
  • Rapid Advance (Customer Cycle)After starting a customer cycle, press HI TEMP
  • Sales Demo Mode ExitRun Service Diagnostics Cycle to clear Demo mode.
  • Service Access Code (free-vend models only)1. Open the door. 2. Within 10 seconds, press in sequence
  • Service Diagnostic Test Modes1. Disconnect power and remove service door (PD models) or remove AA1 jumper from IU control board…
  • Service Diagnostics Cycle1
  • Setup Mode (Control Set-Up)["PD Models
  • Setup/Configuration Mode["PD models
  • Setup/Configuration Mode (PD models)Insert key into service access door, turn and lift to remove the service access door.
  • Setup/Configuration Mode (PR models)Insert setup card (from card reader manufacturer) into card reader
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Washer Cleaning Program["Enter Diagnostic Mode (Blink Mode).","Press BRIGHT button while the display is blinking."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Caloric dishwasher models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax