Error code reference

Maytag Washer Error Code 0

No code (no fault present).

Maytag codesMaytag washer codes

No code (no fault present).

MyPros+ Max

Get the full diagnostic procedure for 0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0 means on a Maytag washer

Error code 0 on a Maytag washer indicates that no fault code is currently stored or active in the control board's memory. This is a neutral status readout, not a malfunction indicator. It appears when a technician or homeowner enters the diagnostic or service mode and the board has nothing logged, either because no fault has occurred or because a previous code was successfully cleared after a repair or reset.

For homeowners, seeing '0' during a code retrieval attempt is actually good news. It means the control board has not detected any electrical or mechanical fault in the wash system. If your washer prompted you to check for codes because of a symptom like stopping mid-cycle or not spinning, the absence of a stored code suggests the issue may have been intermittent, resolved itself after a power reset, or may require a different diagnostic approach since the board did not capture a fault.

If your washer is behaving abnormally despite showing no stored code, the next step is to run a manual diagnostic cycle or inspect components directly. A code 0 does not rule out a physical problem such as a clogged drain, an unbalanced load, or a loose connection that has not yet caused the board to log a fault.

Source: manufacturer service documentation.

Common causes of 0

  1. 01

    No fault has occurred

    Wiring / connection

    The washer is operating normally and the control board has not detected any out-of-range condition in any monitored circuit or component. Code 0 is the expected result when entering diagnostics on a machine with no issues.

  2. 02

    Previous fault code was cleared by power reset

    Wiring / connection

    Unplugging the washer or tripping the circuit breaker clears stored fault codes on many Maytag models. If a fault occurred earlier but the machine was reset before codes were retrieved, code 0 will appear in place of the original fault.

  3. 03

    Intermittent fault not yet captured by the control board

    Wiring / connection

    Some electrical or mechanical issues only trigger a logged code under specific conditions. If the symptom is real but inconsistent, the board may not have reached its threshold to store a code, resulting in a code 0 readout.

  4. 04

    Incorrect diagnostic mode entry

    Wiring / connection

    If the code retrieval sequence was not entered correctly, the display may default to showing 0 rather than any stored fault. Repeating the diagnostic entry procedure according to the service manual for the specific model will confirm whether codes are present.

See the test procedure for each cause

Frequently asked questions about 0

What does error code 0 mean on a Maytag washer?
Error code 0 means no fault code is currently stored in the washer's control board memory. It is not an error in the typical sense. You will see this when you enter diagnostic mode and the board has nothing to report, either because the machine is functioning correctly or because any previous code was cleared by a power reset.
Can I still use my Maytag washer if it shows code 0?
Yes. Code 0 is not a fault condition and does not indicate a problem that would make the washer unsafe or non-functional to operate. If you checked codes because the washer was behaving oddly, you can run a wash cycle and monitor whether a specific fault code appears during operation.
Why does my Maytag washer show 0 when I check for error codes?
Code 0 appears when the control board has no stored faults. This happens when the machine is operating normally, when a previous fault code was erased by unplugging the unit, or occasionally when the diagnostic mode sequence was not entered correctly. If you suspect a problem, re-enter the diagnostic mode carefully and run a test cycle to allow any active fault to register.
How do I fix error code 0 on a Maytag washer?
Code 0 requires no fix because it signals the absence of a detected fault. If your washer has a real symptom such as not draining or not agitating, code 0 means the board has not logged a cause yet. In this case, inspect physical components like the lid switch, drain hose, and pump filter manually, or run a full diagnostic cycle to try to reproduce the fault under monitored conditions. If symptoms persist without a code ever appearing, a service technician can run live sensor tests to identify the problem.
How much does it cost to repair a Maytag washer showing code 0?
There is no repair cost tied directly to code 0 since it is not a fault code. If you are seeing code 0 but the washer has an underlying problem that has not yet triggered a logged fault, repair costs will depend entirely on what that issue turns out to be once diagnosed. A service call to have a technician run diagnostics typically runs between $75 and $150 before any parts or labor for an actual repair.

Related Maytag washer codes

All Maytag washer codes
View all 404 Maytag washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass