mypros+
Model reference

Amana RR-1010/P75414-4M

Microwave

7 documents107 error codes43 service modes

Available documentation

Tech Sheet

  • wiring diagram-a.pdf1 pg
    Covers this model
  • FICHE TECHNIQUE - 8304417 - Rev B16 pg
    Covers this model
  • techsheet-w10420006-reva_W1042000656 pg
    Covers this model
  • Tech Sheet - W10393006 - Rev B52 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 39791166 pg
    Covers this model

Installation Guide

  • Installation Instructions5 pg
    Covers this model

Other

  • tech-sheet-W10865055-RevA60 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RR-1010/P75414-4M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (107)

CodeMeaning
AFRestricted/low air flow detected that may affect dryer performance.d10/F31Overheating of motord11/F11Washer MCU errord12/F25Tachometer errord13Coin 2 errord14/F33Pump disconnectedd15/F34Load detected in washer during Washer Cleanout Cycle.d16Generation 2 debit card reader errord17/F22Door lock errord19/F29Door unlock errord2/F22Dryer exhaust thermistor open errord20/F28Communication failure between CCU and MCU.d21/F27Overflow conditiond22/F70Communication failure from CCU to UICd23/F70Washer communication failure between CCU and UIC.d23/F71Communication failure from UIC to CCUd24/F24Temperature sensor errord3/F23Dryer exhaust thermistor shorted errord3/F73Washer UIC failured3/F74Washer UIC failured4/F01Dryer motor control circuit errord4/F26Door switch errord5Coin 1 errord6/F01Washer CCU errord7/F20No water detected entering washerd8/F21Long draind8/F73UIC Microprocessor errord8/F74UIC EEPROM errord9Low voltage detection errorF0 E7Control board recognized line voltage below 90 VAC.
View all 107 error codes
f01Dryer motor control circuit errorf1 e1Primary control failure.F1 E4UIC (User Interface Control) fault detected.F1 E7ACU voltage input fault.F11MCU errorF1E1Indicates a Cycle Control Unit (CCU) problem.F1E3Incorrect controller installed (electric models only); ACU and/or UI part…F1E5ACU parameter file missing; parameter memory invalid.F2 E0Keypad (keyboard) faultf2 e1Stuck button or user interface mismatch (only appears in service diagnostic…F2 E2Upper dryer keypad is sensed pressed for 60 seconds (stuck key).F20No water detected entering washerF21Long drainf22Exhaust thermistor open errorf23Exhaust thermistor shorted errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between CCU and MCUF29Door unlock errorF2E1Indicates a stuck button (depressed for over 20 seconds) or UI mismatch; only…F2E2User Interface Software ErrorF2E4UI software errorF2E5UI software errorf3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is open (only appears in service diagnostic mode).f3 e7Moisture sensor strip has shorted (only appears in service diagnostic mode).F31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F3E1Exhaust thermistor is open; temperature drops below 18°F (>50k ohms).F3E2Exhaust thermistor has shorted; temperature above 250°F (<500 ohms).F3E3Inlet thermistor is open; temperature drops below 18°F (>245k ohms)F3E4Inlet thermistor is shorted; temperature above 760°F (<20 ohms)F3E5Moisture Sensor 2 Open/Shorted (only Quad Sense models).F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4 E1Microwave oven convection thermistor fault.F4 E2Microwave oven internal temperature sensor fault.F4 E4Microwave oven humidity sensor fault.F4E1No voltage detected at the heater relayF4E2Heater 2 failure or connector problem (electric models only); no voltage…F4E3Restricted air flow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50V) detected at the CCU.F5No feature identified for microwaveF5 E0Door and latch switch do not agreeF5 E1Door latch not operatingF5 E6Upper dryer door circuit error.F6 E1Communication failure between ACU and UIC.F6 E5No cavity size commandF6E1Communication between the CCU and UI has not been detected (UI to CCU).F6E2Communication between the CCU and UI has not been detected (CCU to UI).F6E3Communication errorF7 E6Lower dryer motor circuit error.F7 E7Upper dryer motor circuit error.F7 E8Lower dryer motor sense errorF7 E9Upper dryer motor sense errorf70Communication failure from CCU to UICf71Communication failure from UIC to CCUf73UIC microprocessor errorf74UIC EEPROM errorf8 e1No voltage detected at the water valve relay (steam models only, only appears…FC E1Model/Serial number not programmed into control.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software uploaded from USB stick does not match the model number of the machine.FC E6Model setup export failureFC E7Model setup import failureFC E8Wi-Fi module not responding or not connected.FP E1Coin 1 circuit errorFP E2Coin 2 circuit errorFP E3Card reader communication error.L2Low L2 voltage (less than 50V) detected at the CCU.pfPower failure occurred while the dryer was running.

Service modes (43)

  • Cavity size programming["Disconnect oven or interrupt power","Wait 10 seconds, reconnect power","Enter diagnostic mode
  • Clear last fault code["Disconnect oven or interrupt power","Wait 10 seconds, reconnect power","Enter diagnostic mode
  • Component ActivationFrom Service Diagnostics Diagnostics Home screen, select 'Component Activation'
  • Customer-Focused Drying Mode Adjustment1
  • Customer-Focused Dryness Level Adjustment1. Turn cycle selector knob to an automatic cycle. 2. From the Automatic Cycle Main Screen, press…
  • diagnosticPress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
  • Diagnostic component activation["Enter diagnostic mode (OFF, OFF, START)","Press Bake to activate bake relay","Press Broil once…
  • Diagnostic mode["Press OFF","Press OFF","Press START","If the appliance does not enter diagnostic mode, repeat the…
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM
  • Dryer Field Diagnostic Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM
  • Fahrenheit/Celsius selection["Press OPTIONS then 1"]
  • Fault Code Display and Clear["Activate Service Diagnostic Mode first.","Press and release the 3rd button to display the most…
  • Fault/Error Code Display and Clear1. Activate Service Diagnostic Mode. 2. Press and release the 3rd button to display next error…
  • helpPress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
  • Help Mode["Press the lower left (PERM
  • Install Diagnostics1
  • Key Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • model_serial_number_menuEnter Help Mode first
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Quick Diagnostic TestFrom Diagnostics Home screen, select 'Error Diagnostic', then select 'Quick Diagnostic Test'
  • Reset Modifiers and Options to Factory Default1
  • Service Diagnostic Mode["1
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Test Mode["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Set-up Mode["PD/PR Models
  • setupPD Models
  • Setup Mode["Stacked PD Models
  • Software Version Display1
  • Temperature calibration adjustment["Press OPTIONS then 6","For double oven only, select desired oven (upper or lower)","Press 3 to…
  • UI Component TestFrom Diagnostics Home screen, select 'Component Activation', then select 'UI Component Test'
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • usb_menuEnter Help Mode first
  • User Interface/Control System Test1
  • Washer Cleanout Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center right (BRIGHTS) button."]
  • Washer Cleanout Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (BRIGHTS) button."]
  • Washer Cycle Credit (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (PERM
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center left (WHITES) button."]
  • Washer Manual Overview Test Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (DELICATES AND KNITS)…
  • Washer Quick Overview Test Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (DELICATES AND KNITS)…
  • Washer Quick Spin Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center middle (COLORS) button."]
  • Washer Quick Spin Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (COLORS) button."]
  • wi-fi_menuFrom the F0 screen in setup mode, press HEAVY DUTY keypad to enter Wi-Fi mode

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass