mypros+
Error code reference

Maytag Washer Error Code F01

Dryer motor control circuit error

Maytag codesMaytag washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F01 error code actually means

Your Maytag washer has detected a problem with the electrical circuit that controls the wash motor, and it cannot tell exactly which part of that circuit has failed. As a safety measure, the washer has shut down all wash cycles until the issue is addressed and the error is manually cleared. This is not a simple glitch and typically requires inspecting or replacing the control board or motor.

Diagnostic procedure

The full F01 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F01 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F01

Ranked by how often they cause this code
  1. 1Faulty main control board
  2. 2Stuck or welded motor relay contacts
  3. 3Shorted motor relay drive circuit
  4. 4Defective drive motor
  5. 5Loose or corroded wiring connections

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F01

What does F01 mean on a Maytag washer?
F01 indicates a motor control circuit error where the washer's control board cannot determine the condition of the motor relay. It may be caused by a stuck relay, a shorted relay drive circuit, or a defective relay feedback circuit. All wash cycles and the display are disabled until the fault is manually cleared. This code requires hands-on diagnosis to identify the specific failed component.
Will resetting my Maytag washer clear the F01 error code?
A manual reset may temporarily clear the F01 code and allow the washer to operate, but if the underlying circuit fault is still present, the code will return. The error description specifically states the unit remains disabled until manually cleared, but clearing the code is not the same as fixing the problem. A proper repair of the faulty relay circuit or control board is needed for a lasting resolution.
How much does it cost to repair an F01 error on a Maytag washer?
Repair costs vary depending on which component has failed. A main control board replacement typically runs in the range of $150 to $350 for parts and labor combined, while a drive motor replacement can range from $200 to $450 depending on parts and service rates in your area. If the issue is limited to wiring or connectors, the cost may be significantly lower. Getting a diagnostic visit from a technician will help narrow down the exact repair needed before committing to parts.
Can I fix the F01 error on my Maytag washer myself?
Some DIY steps are possible, such as inspecting and reseating wiring harness connectors at the control board and motor. However, if the fault lies within the control board itself, such as a failed relay or driver component, board replacement is typically required. Unless you are comfortable working with appliance electronics and testing components, this repair is best handled by a qualified technician.
Is it safe to use my Maytag washer when F01 is displayed?
The washer disables all cycles when F01 is active, so normal operation is not possible in this state. Attempting to force operation without resolving the underlying motor relay fault could risk further damage to the control board or drive motor. It is best to keep the washer out of service until the fault is properly diagnosed and repaired.

Related Maytag washer error codes

All Maytag washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass