mypros+
Model reference

Whirlpool 3LCHW9100WQ0

Washer

4 documents21 error codes15 service modes

Available documentation

Tech Sheet

  • Lave-linge Commercial À Chargement Frontal (Export) - OpÉrations De Base16 pg
    Covers this model
  • Tech Sheet - W10222793 - Rev A16 pg
    Covers this model

Quick Reference

  • Quick Reference Manual5 pg
    Covers this model

Installation Guide

  • Installation Instructions Semi-Pro Front-Load Washer52 pg
    Covers this model
MyPros+ Max

Diagnose your Whirlpool 3LCHW9100WQ0.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (21)

CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF01Central Control Unit (CCU) communication error; the pump drive in the CCU…F11Motor Control Module (MCM) failure, possibly due to repeated under-voltage or…F20No water entry detected in the washer; the first pressure switch threshold is…F21Excessive drain time; drain operation exceeds 8 minutes without reaching the…F22Door lock error; the washer made multiple door lock attempts and failedF24Water temperature sensor error; the sensor value is out of range (-5°C to 103°C…F25Tachometer error; the CCU cannot correctly detect the motor speed, causing the…F26Door switch error; the door switch circuit remains open for 5 seconds while the…F27Overflow condition; the overflow switch of the pressure switch is closed for…F28Communication failure between the Central Control Unit (CCU) and Motor Control…F29No description availableF30No description availableF31No description availableF34Load detected in washer during Washer Cleanout Cycle.F70Communication failure between CCU and UI (User Interface).F73User Interface (UI) failure; communication error in the User Interface…F74User Interface (UI) failure; communication error in the User Interface (same as…

Service modes (15)

  • Code Display Mode["Can only be accessed when the washer is in error state.","PD Models
  • Diagnostic Mode (Blinking Mode)["First access Setup Mode (Operating Set-up).","Press and hold DELICATES & KNITS button for 1…
  • Help Mode["PD Models
  • Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
  • Help Mode (PD Models)["Open the service door.","Press the WOOLENS key until the display reads 2.XX.","Press the…
  • Machine Clean Cycle["Enter Blinking Mode (Diagnostic Mode).","Press BRIGHT button while display is blinking."]
  • Manual Overview Test["Enter Blinking Mode (Diagnostic Mode).","Press WHITES button while display is blinking."]
  • Quick Drain and Spin["Enter Blinking Mode (Diagnostic Mode).","Press COLORS button while display is blinking."]
  • Quick Overview Test["Enter Blinking Mode (Diagnostic Mode).","Press WOOLENS button while display is blinking."]
  • Service Access Code["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and the…
  • Service Access Code (Keyless Entry to Service Mode)["Only works on washers configured for $0 sale price without Special Price, and Coin/Debit option…
  • Setup Mode (Operating Set-up / Programming Mode)["PD Models
  • Setup Mode (PD Models)["Insert access door key, turn, and lift to remove access door.","Use lower fabric setting key pads…
  • Setup Mode (PN Models)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
  • Washer Diagnostic Mode (Flashing Mode)["First enter 'Start Operating Set-Up' mode.","Then press and hold the DELICATES & KNITS key pad…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Whirlpool washer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax