mypros+
Error code reference

Maytag Washer Error Code E302

Mitsubishi inverter overcurrent alarm (OC3).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E302 error code actually means

Your Maytag washer has detected that too much electrical current is flowing through the part that controls the wash motor's speed, and the machine has shut itself off to prevent further damage. This is most often caused by a short circuit or a problem with the motor or its wiring. The washer will not operate normally until the underlying electrical fault is found and repaired.

Diagnostic procedure

The full E302 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if there is a short circuit on the output of the Inverter.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E302 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E302

Ranked by how often they cause this code
  1. 1Short circuit on inverter output wiring
  2. 2Failed or shorted wash motor windings
  3. 3Mechanically seized or dragging motor
  4. 4Failed inverter board with damaged output transistors
  5. 5Loose or corroded motor connector pins

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E302

What does E302 mean on a Maytag washer?
E302 indicates a Mitsubishi inverter overcurrent alarm (OC3), meaning the inverter drive that controls wash motor speed has detected excessive current on its output. The machine shuts down automatically to protect the inverter electronics and motor. This fault points to a short circuit, motor fault, or inverter board failure that must be diagnosed before the washer can run safely.
Is it safe to keep using my washer with the E302 code?
No. The E302 code represents an active electrical fault involving excess current in the motor drive circuit. Continuing to run the washer risks damaging the inverter board, motor windings, or associated wiring, and could create a fire or shock hazard. The machine should remain unpowered until the root cause is identified and corrected.
How much does it cost to repair an E302 error on a Maytag washer?
Repair costs vary depending on the failed component. A wiring harness repair or connector service is typically the least expensive route, often falling in the range of $75 to $200 including labor. A replacement wash motor can range from $150 to $400 with installation. An inverter board replacement is generally the most costly single component repair, with parts and labor typically ranging from $200 to $500 or more depending on the specific model and service rates in your area.
Can I fix the E302 error myself?
Some aspects of diagnosis are accessible to a knowledgeable DIYer, such as inspecting the wiring harness for visible damage, checking connector terminals, and testing motor winding resistance with a multimeter. However, if the fault traces back to the inverter board or motor internals, those components require replacement and some comfort with appliance disassembly. Working around inverter drive electronics involves capacitors that can hold charge after power is removed, so proper precautions are important.
Will resetting the washer clear the E302 error?
A power reset may temporarily clear the displayed code, but it will not resolve the underlying fault. If a short circuit, motor problem, or inverter failure is present, the OC3 alarm will return as soon as the inverter attempts to drive the motor again. A reset is only appropriate after the physical cause has been found and repaired.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass