mypros+
Error code reference

Maytag Washer Error Code E327

24VDC short circuit on the 24VDC power output (PC terminal).

Maytag codesMaytag washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E327 error code actually means

Your Maytag washer has detected an electrical short in one of its internal power circuits, specifically a low-voltage line that helps control the motor and other components. This is a protective shutdown designed to prevent further damage to the electronics. The machine will not operate normally until the source of the short is found and corrected.

Diagnostic procedure

The full E327 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check for short circuit on the Inverter control terminals.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E327 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E327

Ranked by how often they cause this code
  1. 1Damaged or pinched wiring harness at inverter terminals
  2. 2Failed inverter control board
  3. 3Short circuit in a downstream 24VDC load
  4. 4Connector corrosion or moisture intrusion at PC terminal
  5. 5Loose or incorrectly seated inverter connector

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E327

What does E327 mean on a Maytag washer?
E327 indicates a short circuit has been detected on the 24VDC power output at the PC terminal of the inverter control board. The inverter monitors this low-voltage supply line and shuts down operation when it detects an abnormal load or direct short. The fault can originate in the inverter board itself, the connecting wiring harness, or a downstream component drawing power from that circuit. The washer will not run normally until the short is identified and corrected.
Is it safe to keep using my Maytag washer when E327 appears?
No, you should not continue operating the washer while E327 is active. A short circuit on the 24VDC line can cause the inverter board to overheat or sustain further damage if the machine is forced to run. The error is a protective shutdown, and running cycles through it risks escalating a repairable fault into a more expensive failure.
How much does it cost to repair a Maytag washer with error code E327?
Repair costs depend on which component is causing the short. If the fix involves re-seating a connector or replacing a wiring harness section, costs are typically in the range of $75 to $200 including labor. If the inverter control board has failed internally and requires replacement, parts and labor combined often range from $200 to $450 depending on parts availability and local service rates.
Can I fix E327 on my Maytag washer myself?
Some causes of E327 are accessible to a knowledgeable DIYer, such as re-seating a loose connector or inspecting the wiring harness for visible damage. However, diagnosing a short circuit accurately requires a multimeter and understanding of how to safely isolate inverter terminals. If the fault points to the inverter control board itself, replacing that board involves working near high-voltage components and is best handled by a qualified technician.
Will resetting the washer clear the E327 error code?
A reset may temporarily clear the displayed error, but E327 will return immediately or during the next cycle if the underlying short circuit is still present. Resetting without repairing the fault does not correct the electrical condition and provides no lasting resolution. The error should be fully diagnosed and the short eliminated before expecting normal operation to resume.

Related Maytag washer error codes

All Maytag washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass