mypros+
Error code reference

Maytag Washer Error Code 9E

Malfunction in dryer door circuit.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 9E error code actually means

The 9E code means your Maytag appliance detected a problem with the door circuit, specifically that it cannot confirm the door is properly closed and secured. Think of it as a safety system that stopped the machine because it was not sure the door was latched correctly. Try unplugging the machine for one minute and plugging it back in to see if the issue clears on its own.

Diagnostic procedure

The full 9E procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Disconnect power to dryer for one minute. Investigate and correct condition which led to error code response.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 9E procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 9E

Ranked by how often they cause this code
  1. 1Faulty door switch
  2. 2Damaged or disconnected wiring harness
  3. 3Broken or misaligned door latch
  4. 4Corroded or loose connector terminals
  5. 5Failed control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 9E

What does 9E mean on a Maytag washer?
The 9E code indicates a malfunction in the door circuit, meaning the control board cannot confirm the door is properly closed and latched. This is a safety fault that stops the machine from operating until the issue is resolved. The code can result from a failed door switch, damaged wiring, a broken latch, or a control board problem.
Is it safe to use my Maytag appliance when the 9E code is showing?
No, you should not attempt to operate the appliance while the 9E code is active. The fault indicates the door circuit is not functioning correctly, and the machine will not run in this state as a safety precaution. Using a machine with a compromised door circuit could present a safety risk, so the underlying problem should be corrected before resuming use.
Will resetting my Maytag washer clear the 9E error code?
A reset, performed by disconnecting power for one minute and then restoring it, is the recommended first step and can clear the code if it was triggered by a temporary glitch. However, if a physical component such as the door switch, latch, or wiring is actually damaged, the code will return after the reset once the machine attempts to verify the door circuit again. A reset is a diagnostic starting point, not a permanent fix for a hardware failure.
Can I fix the 9E error code myself?
Some causes of the 9E code are DIY-friendly. Start by disconnecting power for one minute and then restoring it to see if the error clears. If it returns, inspect the door latch for visible damage and check that all wiring connectors in the door circuit are fully seated. Replacing a door switch or latch is a manageable repair for someone comfortable working with appliance components, but control board replacement is more complex and may warrant professional service.
How much does it cost to repair a 9E error code on a Maytag washer?
Repair costs vary depending on the failed component. A replacement door switch typically costs between $15 and $50 for the part, while a door latch assembly can range from $20 to $75. If the control board is at fault, parts alone can run between $100 and $300 or more. Adding professional labor will increase total costs, generally ranging from $100 to $250 depending on your location and the complexity of the repair.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass