mypros+
Error code reference

Maytag Washer Error Code F25

Tachometer error; the MCC cannot correctly detect the motor speed, causing the washer to stop

Maytag codesMaytag washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F25 error code actually means

Your Maytag washer is displaying F25 because it cannot properly read how fast the motor is spinning, so it stopped to protect itself. This could be caused by something as simple as a loose wire, a worn belt, or a forgotten shipping bolt left in from installation. The washer's door may stay locked for about 2 minutes after this error appears if it happened during the spin cycle, which is normal.

Diagnostic procedure

The full F25 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Clear the error code, unplug the washer, verify the belt is not broken, check that shipping system has been removed, and check electrical connection between MCM and drive motor connector.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F25 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F25

Ranked by how often they cause this code
  1. 1Loose or faulty MCM to motor electrical connection
  2. 2Broken or worn drive belt
  3. 3Shipping system not fully removed
  4. 4Failed drive motor or tachometer
  5. 5Failed Motor Control Module (MCM)

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F25

What does F25 mean on a Maytag washer?
F25 is a tachometer error indicating the Motor Control Module cannot correctly detect the drive motor's speed. When this signal is lost or unreliable, the washer stops to prevent damage. If the error occurs during high-speed spin, the door will remain locked for approximately 2 minutes before releasing.
Is it safe to use my Maytag washer when the F25 code is showing?
You should not continue running the washer while the F25 error is active. The washer stops automatically when it detects the fault to prevent potential motor damage. Attempting to force cycles through repeated resets without diagnosing the root cause can worsen the underlying problem.
How much does it cost to repair a Maytag washer F25 error?
Repair costs vary depending on the cause. Reconnecting a loose wiring harness costs nothing beyond your time. A replacement drive belt typically runs in the range of $15 to $40 for the part. A drive motor replacement can range from $100 to $250 or more for the part, and a new Motor Control Module can cost anywhere from $100 to $300 or more, not including labor if a technician is needed.
Can I fix the F25 error myself without calling a technician?
Some causes of F25 are DIY-friendly. Start by unplugging the washer, then check that all shipping hardware has been removed, inspect the drive belt for damage, and reseat the electrical connector between the MCM and the drive motor. If these steps do not resolve the issue, motor or control board testing may require a technician.
Will resetting the washer clear the F25 error?
Clearing the error code is the recommended first diagnostic step, and a reset may temporarily clear the display. However, if the underlying cause such as a bad connection, broken belt, or failed motor component is not corrected, the F25 code will return during the next cycle.

Related Maytag washer error codes

All Maytag washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass