mypros+
Error code reference

Bosch Dishwasher Error Code 5

Water intake period exceeds 5 minutes.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the 5 error code actually means

Your Bosch dishwasher tried to fill with water but it took too long, so the machine stopped and displayed this error to protect itself. This usually means the water supply to the dishwasher is restricted or the water pressure is too low. Checking that the water tap under the sink is fully open and that no hoses are kinked is a good first step.

Diagnostic procedure

The full 5 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if water tap is closed, strainers are blocked, water pressure is below 1 bar at inlet valve.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock 5 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of 5

Ranked by how often they cause this code
  1. 1Closed or partially closed water supply tap
  2. 2Clogged inlet strainer
  3. 3Low incoming water pressure
  4. 4Faulty or stuck inlet solenoid valve
  5. 5Failed water level sensor

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about 5

What does 5 mean on a Bosch dishwasher?
Error code 5 on a Bosch dishwasher means the dishwasher attempted to fill with water but the intake period exceeded 5 minutes without reaching the required water level. The machine stops the cycle and displays this code to prevent operating without adequate water. The most common causes are a restricted water supply, low water pressure below 1 bar, or a blocked inlet strainer.
Is it safe to keep using my Bosch dishwasher when error code 5 appears?
You should not attempt to run the dishwasher while error code 5 is active. The machine has stopped the cycle specifically because it could not confirm adequate water intake, and running a wash cycle without sufficient water can damage the pump and heating element. Resolve the underlying supply or component issue before resuming normal use.
How much does it cost to repair a Bosch dishwasher showing error code 5?
If the fix is simply opening a shutoff valve or cleaning a strainer, there is no parts cost involved. If the inlet solenoid valve needs replacement, parts typically range from $25 to $75 depending on the model, plus labor if a technician is hired. A failed water level sensor is generally in a similar price range for the part itself. Total repair costs including professional labor can range from $80 to $200 or more depending on the specific component and your location.
How do I fix error code 5 on my Bosch dishwasher?
Start by confirming the water supply tap under the sink is fully open and that the supply hose is not kinked. Next, check the inlet strainer at the valve connection for sediment or debris and clean it if needed. If the water supply and strainer are clear, verify that your household water pressure meets the minimum 1 bar requirement at the inlet. If the issue persists after these checks, the inlet valve or water level sensor may need to be tested and possibly replaced.
Will resetting my Bosch dishwasher clear error code 5?
A reset may clear the error display temporarily, but the code will return if the underlying cause has not been addressed. Resetting without fixing the water supply restriction, low pressure, or faulty component will result in the dishwasher timing out on the next fill attempt and throwing the error again. Always diagnose and correct the root cause first.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass