mypros+
Error code reference

Bosch Dishwasher Error Code F1

Temperature stop fault

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F1 error code actually means

The F1 code means your dishwasher's water is not heating up fast enough during the wash cycle. The machine noticed the water temperature barely changed over a ten-minute period, so it skipped the heating step and kept running. Your dishes may not be getting properly cleaned or sanitised as a result.

Diagnostic procedure

The full F1 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check: Element, thermistor, water level, circulation pump and control unit, wiring.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F1 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F1

Ranked by how often they cause this code
  1. 1Failed heating element
  2. 2Faulty NTC thermistor
  3. 3Low water level in the tub
  4. 4Circulation pump fault
  5. 5Wiring or control unit fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F1

What does F1 mean on a Bosch dishwasher?
F1 on a Bosch dishwasher indicates a temperature stop fault. The control unit detected that the water temperature rose less than 5°C over a ten-minute period during the heating stage. The machine exits the heating phase and continues running, but the water has not reached the proper temperature for effective washing. Components involved include the heating element, NTC thermistor, circulation pump, water level, and wiring.
Is it safe to keep using my dishwasher when it shows F1?
The dishwasher will complete its cycle after logging F1 by skipping the heating stage, so it will not shut down abruptly or cause an immediate safety hazard. However, running repeated cycles without proper water heating means dishes are not being sanitised effectively and detergent may not dissolve or activate correctly. It is advisable to diagnose and resolve the fault before relying on the appliance for regular use.
Will resetting the dishwasher clear the F1 error?
A reset may clear the F1 code temporarily, but the error will return if the underlying fault is not repaired. Because F1 is triggered by a measurable condition during the heating stage, the code will reappear as soon as the dishwasher runs a cycle and the temperature rise threshold is not met again. A reset is useful for confirming whether the fault is intermittent, but it is not a fix on its own.
Can I fix the F1 error myself?
Some causes of F1 are accessible to a confident DIYer. You can check the water fill level, inspect wiring connections for corrosion or looseness, and test the heating element for continuity with a multimeter. Thermistor and circulation pump testing requires a bit more technical knowledge. Control board replacement is generally best left to a qualified technician.
How much does it cost to repair a Bosch dishwasher F1 error?
Repair costs vary depending on which component has failed. A replacement heating element typically runs in the range of $40 to $120 for the part alone. An NTC thermistor is usually less expensive, often $15 to $50. Circulation pump replacement can range from $80 to $200 or more for parts. Adding professional labour costs will increase the total, with most technician service calls ranging from $100 to $300 depending on your location and the extent of the repair.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass