mypros+
Error code reference

Daewoo Refrigerator Error Code D0

Door switch malfunction detected when door switch is left open continually for one hour.

Daewoo codesDaewoo refrigerator codes

Door switch malfunction detected when door switch is left open continually for one hour.

First step from the service manual

Check door switch; R-fan and F-fan operate irrespective of door switch when compressor is on.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for D0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What D0 means on a Daewoo refrigerator

The D0 error code on a Daewoo refrigerator indicates that the door switch has been detected in the open position continuously for one hour. The door switch is a small electrical component that tells the refrigerator's control board whether the door is open or closed. Under normal operation, this signal changes frequently as the door is opened and closed. When the control board registers an uninterrupted open-door signal for 60 consecutive minutes, it concludes that the switch has malfunctioned rather than assuming the door has genuinely been left open that long.

The door switch plays a role in managing the refrigerator and freezer fan motors. Normally, when a door is opened, the fans are disabled to prevent warm air circulation inside the cabinet. A stuck-open switch signal would cause the fans to shut off and stay off during normal compressor operation, reducing cooling efficiency. To compensate for this, when D0 is active and the compressor is running, the control board overrides the faulty switch signal and forces both the R-fan (refrigerator compartment fan) and F-fan (freezer compartment fan) to operate regardless of the switch state.

Common causes of this fault include a physically damaged or stuck door switch, broken or shorted wiring in the switch harness, and in some cases an actual door alignment issue where the door is not fully closing and pressing the switch. The switch mechanism itself can wear out over time or become obstructed by ice buildup or debris, preventing it from returning to the closed position after the door is shut.

Source: manufacturer service documentation.

Common causes of D0

  1. 01

    Faulty or stuck door switch

    Part replacement

    The door switch contacts can wear out or become stuck in the open position over time, causing the control board to receive a continuous open-door signal. Inspect the switch for visible damage and test whether the button depresses and springs back freely.

  2. 02

    Damaged wiring or harness connection

    Wiring / connection

    A broken wire, corroded connector, or loose harness connection between the door switch and the control board can mimic a stuck-open switch signal. Inspect the wiring leading to the switch for cuts, pinching, or corrosion at the connector terminals.

  3. 03

    Ice or debris blocking the switch

    Wiring / connection

    Ice buildup or food debris around the door frame can physically prevent the switch actuator from being pressed when the door closes. Check the area around the switch for any obstruction and clear it before replacing any parts.

  4. 04

    Door misalignment or worn door gasket

    Wiring / connection

    If the refrigerator door is sagging or the gasket has deformed, the door may not be making adequate contact with the switch plunger when closed. Check that the door closes squarely and that the gasket seals evenly around the frame.

  5. 05

    Control board fault

    Part replacement

    In rare cases, the main control board may incorrectly interpret the door switch signal even when the switch itself is functioning correctly. This should only be considered after the switch, wiring, and door alignment have been ruled out as causes.

See the test procedure for each cause

Frequently asked questions about D0

What does D0 mean on a Daewoo refrigerator?
The D0 error code means the refrigerator's control board has detected a door switch malfunction. Specifically, the door switch has been reading in the open position continuously for one hour. The control board interprets this as a switch failure rather than a genuinely open door, and it overrides the switch to keep the fans running while the compressor is on.
How do I fix a D0 error on a Daewoo refrigerator?
Start by inspecting the door switch for physical damage, debris, or ice buildup that might be preventing it from engaging when the door closes. Check the wiring harness connected to the switch for any loose, broken, or corroded connections. If the switch is confirmed faulty, replacing it is typically the fix. Also verify the door is properly aligned so it makes full contact with the switch when closed.
Will resetting the refrigerator clear the D0 error code?
A power reset may temporarily clear the D0 code, but the error will return if the underlying door switch issue has not been resolved. Since the code triggers after one hour of continuous open-switch signal, the fault will reappear once that condition is met again. The root cause must be corrected to permanently clear the error.
Is a D0 error on my Daewoo refrigerator a safety concern?
A D0 error is not an immediate safety hazard, but it does affect cooling performance. The refrigerator compensates by running the fans independently of the switch, which helps maintain temperatures. However, leaving the fault unaddressed can lead to reduced efficiency and potential food spoilage over time, so the switch should be inspected and repaired promptly.
How much does it cost to repair a D0 door switch error on a Daewoo refrigerator?
If only the door switch needs replacement, parts typically cost in the range of $10 to $40 depending on the specific model. If professional repair labor is needed, total costs including diagnosis and parts can range from $80 to $200. Wiring repairs or a control board replacement, if required, would place the cost at the higher end of that range or above.

Related Daewoo refrigerator codes

All Daewoo refrigerator codes
View all 30 Daewoo refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass