Error code reference

Electrolux Refrigerator Error Code CE

Ice maker communication lost between main board and ice maker control board (displayed as Ice in freezer, CE…

Electrolux codesElectrolux refrigerator codes

Ice maker communication lost between main board and ice maker control board (displayed as Ice in freezer, CE in fresh food).

First step from the service manual

Go to flow chart 50C. Put into service mode to verify.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for CE.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What CE means on a Electrolux refrigerator

The CE error code on an Electrolux refrigerator indicates a fault detected within the main control board itself. The board has run an internal self-check and flagged an error it cannot resolve through normal operation. This code displays as 'ER' flashing alongside 'CE' on the control panel. The first response is always a hard reset: cut power to the unit for at least 15 seconds, then reapply. If the code returns, the main control board requires replacement.

For homeowners, the main control board is the central circuit board that manages every function of the refrigerator, including temperature regulation, compressor operation, defrost cycles, and communication between components. When this board reports a CE error, it is essentially signaling that something internal to its own operation has failed or become unstable. The refrigerator may still run partially, but core functions could be compromised.

Because this code points directly at the control board rather than a sensor or external component, there is limited diagnostic work to do beyond the power reset. If the reset clears the code and it does not return, the fault was likely a temporary voltage spike or communication glitch. Persistent CE codes after a reset indicate the board itself needs to be replaced.

Source: manufacturer service documentation.

Common causes of CE

  1. 01

    Temporary control board communication glitch

    Wiring / connection

    A voltage fluctuation or power interruption can cause the main control board to enter a fault state without any hardware damage. A 15-second power reset often clears this condition entirely.

  2. 02

    Failed main control board

    Part replacement

    Internal circuitry on the main control board can fail due to age, heat exposure, or component degradation. When the board's self-diagnostic detects this internal failure, it triggers the CE code, and the board must be replaced.

  3. 03

    Corrupted control board firmware or memory

    Part replacement

    The onboard memory or firmware can become corrupted, causing the control to flag a persistent CE error even when the hardware is otherwise intact. This typically does not resolve with a reset and requires board replacement.

  4. 04

    Power supply issue affecting the control board

    Wiring / connection

    Unstable household voltage, a failing outlet, or a damaged power cord can deliver irregular power to the main control board, triggering fault conditions. Verifying the outlet and cord before replacing the board rules this out.

See the test procedure for each cause

Frequently asked questions about CE

What does the CE error code mean on an Electrolux refrigerator?
The CE code on an Electrolux refrigerator signals a problem with the main control board. It displays as 'ER' flashing with 'CE' on the panel. The board has detected an internal fault through its self-diagnostic routine. This code points directly at the control board, not at an external sensor or component.
How do I fix the CE error code on my Electrolux refrigerator?
Start by cutting power to the refrigerator at the wall outlet or circuit breaker for at least 15 seconds, then restore power. If the CE code clears and does not return, the issue was a temporary glitch. If the code comes back after the reset, the main control board needs to be replaced. Board replacement is a moderate DIY repair if you are comfortable working with appliance electronics and can source the correct part by model number.
Is it safe to keep using my Electrolux refrigerator while the CE code is showing?
Use caution. Because the CE code indicates the main control board itself has a fault, core functions like temperature regulation, defrost cycles, and compressor control may not operate correctly even if the unit appears to be running. Food safety can be at risk if temperatures are not being maintained properly. Check the actual interior temperature with a thermometer, and do not rely on the panel display if the control board is compromised.
How much does it cost to fix a CE error code on an Electrolux refrigerator?
If the power reset clears the code, there is no cost. If the main control board needs replacement, the part typically costs between $100 and $250 depending on the model, with professional labor adding another $100 to $200. DIY replacement is feasible for most models since the board is usually accessible behind the rear panel or inside the control housing, and requires only basic tools and careful handling of the wiring harness connections.
Will unplugging my Electrolux refrigerator fix the CE error?
Unplugging the unit for at least 15 seconds is the recommended first step and does resolve the CE code when the fault was caused by a temporary power fluctuation or communication error. However, if the main control board has a genuine hardware failure, the code will return shortly after power is restored. A one-time successful reset with no recurrence is a good sign the board is intact.

Related Electrolux refrigerator codes

All Electrolux refrigerator codes
View all 92 Electrolux refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass