mypros+
Error code reference

Fisher & Paykel Oven Error Code E008

Not used on these models.

Fisher & Paykel codesFisher & Paykel oven codes

Not used on these models.

MyPros+ Max

Get the full diagnostic procedure for E008.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E008 means on a Fisher & Paykel oven

The E008 error code is listed as not used on these Fisher & Paykel oven models. This means the code is not assigned to any active diagnostic function, sensor, or control system within the firmware of the applicable product range. It does not correspond to a fault condition that the oven's control board is designed to detect, monitor, or report during normal or abnormal operation.

Because this code has no defined function in these models, its appearance on the display would most likely point to a control board anomaly rather than a genuine component failure. Situations such as corrupted firmware, a transient electrical fault, or a control board malfunction could potentially cause the display to show an undefined or placeholder code like E008. In these cases, the code itself does not identify a specific failed part.

If this code does appear on your Fisher & Paykel oven, the recommended approach is to treat it as a control system irregularity. A power cycle may clear the display. If the code persists or the oven behaves abnormally, the control board should be inspected by a qualified technician, as the board may be generating fault signals that do not correspond to any intended diagnostic output.

Source: manufacturer service documentation.

Common causes of E008

  1. 01

    Control board anomaly or firmware glitch

    Wiring / connection

    Since E008 is an unused code, the most likely cause is a transient fault in the electronic control board generating an undefined error signal. A power reset may resolve this.

  2. 02

    Corrupted control board firmware

    Part replacement

    In rare cases, firmware corruption can cause a control board to output placeholder or undefined error codes. This may require a board replacement or firmware update by a technician.

  3. 03

    Faulty or failing control board

    Part replacement

    A control board that is beginning to fail may display undefined codes as internal logic breaks down. If the code is persistent and the oven is not functioning correctly, the board should be tested.

  4. 04

    Transient power supply disturbance

    Wiring / connection

    A power surge, brownout, or brief outage can cause the control board to display erroneous codes. Restoring stable power and resetting the oven typically resolves this.

See the test procedure for each cause

Frequently asked questions about E008

What does E008 mean on a Fisher & Paykel oven?
E008 is listed as not used on these Fisher & Paykel oven models, meaning it has no defined diagnostic function in the oven's control system. Its appearance on the display is not associated with any specific component failure. It most likely indicates a control board glitch, a transient power issue, or a firmware irregularity rather than a broken part.
Can I fix the E008 error on my Fisher & Paykel oven myself?
Since E008 has no assigned meaning on these models, a power cycle is the appropriate first step. Turn the oven off at the circuit breaker for at least five minutes, then restore power and check if the code clears. If it persists or the oven is not working properly, a qualified technician should inspect the control board.
Is it safe to use my Fisher & Paykel oven when E008 is displayed?
Because E008 is not linked to any specific fault condition on these models, it does not by itself indicate a hazardous situation. However, if the oven is behaving abnormally alongside the code, such as not heating correctly or cycling unexpectedly, you should stop using it and have it inspected before continuing.
How much will it cost to repair the E008 error on a Fisher & Paykel oven?
If the issue is a simple transient glitch, a power reset costs nothing. If a control board replacement is needed, parts and labor typically range from $150 to $400 or more depending on the specific model and your location. A diagnostic service call alone usually runs $75 to $150.
Will resetting my Fisher & Paykel oven clear the E008 error?
A reset is the recommended first step when E008 appears, since the code has no defined fault associated with it. Turn off the circuit breaker supplying the oven for five minutes and then restore power. If the code does not return and the oven operates normally, no further action is needed. If it reappears, the control board should be professionally evaluated.

Related Fisher & Paykel oven codes

All Fisher & Paykel oven codes
View all 17 Fisher & Paykel oven codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass