mypros+
Error code reference

Frigidaire Range Error Code F033

Meat probe temperature sensor shorted or too hot (triggered if meat probe sees temperature in excess of 392°F).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F033 error code actually means

Your Frigidaire range is detecting a problem with the meat probe, the thermometer you insert into food while cooking. Either the probe got too hot and was damaged, or it has a short circuit inside it. Unplugging the probe and checking whether the error clears is a good first step.

Diagnostic procedure

The full F033 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Make sure the meat probe was not used in such a way that it could have seen temperatures exceeding 392°F; verify probe is fully inserted into socket.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F033 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F033

Ranked by how often they cause this code
  1. 1Meat probe exposed to excessive heat
  2. 2Probe not fully seated in socket
  3. 3Damaged probe cable or connector
  4. 4Corroded or fouled probe socket
  5. 5Faulty oven control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F033

What does F033 mean on a Frigidaire range?
F033 indicates that the meat probe temperature sensor has been detected as shorted or has registered a temperature above 392°F, which is beyond its rated operating range. The control board monitors the probe's resistance signal continuously, and when that signal falls outside acceptable limits, it locks out operation and displays F033. The fault is meant to prevent inaccurate cooking or further component damage.
Will resetting the range clear the F033 error code?
Performing a reset by cutting power to the range for a few minutes may temporarily clear the display, but the fault will return if the underlying cause is not addressed. If the probe is shorted or damaged, the error will reappear as soon as the probe is reconnected and the oven is powered on. A permanent fix requires correcting or replacing the faulty component.
How much does it cost to fix a Frigidaire F033 error?
If only the meat probe needs replacement, the repair cost is relatively low, generally in the range of $20 to $60 for the part, plus your time if doing it yourself. If the oven probe socket or wiring needs repair, costs can rise to the $100 to $200 range depending on labor. A control board replacement is the most expensive scenario, typically ranging from $150 to $400 or more for parts and labor combined.
Can I fix the F033 error myself, or do I need a technician?
Many cases of F033 can be resolved without a technician by simply removing the meat probe, inspecting it for damage, and reinserting it fully into the socket. If the probe was exposed to very high temperatures or shows physical damage, replacing the probe is a straightforward DIY repair. If a new probe does not clear the fault, further diagnosis of the socket wiring and control board is recommended, and a technician may be needed at that point.
Is it safe to use my Frigidaire range while F033 is showing?
You can typically continue using the range for surface cooking with the meat probe disconnected, as the F033 fault is specifically tied to the probe circuit. However, meat probe-assisted cooking features will not function correctly while the fault is active. It is not advisable to ignore the fault and continue using probe cooking modes, as the temperature readings will be unreliable.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass