mypros+
Error code reference

Frigidaire Range Error Code F098

Magnetron case sensor probe shorted (NTC sensor on the magnetron has failed).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F098 error code actually means

Your Frigidaire range is detecting a problem with a small temperature sensor located on the microwave's internal heating component. This sensor has stopped working correctly, which caused the appliance to shut down as a safety precaution. A technician will need to replace the faulty sensor to get the unit working again.

Diagnostic procedure

The full F098 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Replace NTC sensor.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F098 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F098

Ranked by how often they cause this code
  1. 1Failed NTC thermistor sensor
  2. 2Shorted or damaged sensor wiring harness
  3. 3Moisture or contamination in the sensor probe
  4. 4Heat stress damage to the sensor
  5. 5Faulty control board misreading sensor input

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F098

What does F098 mean on a Frigidaire range?
F098 indicates that the NTC temperature sensor mounted on the magnetron case has been detected in a shorted condition. The sensor is a thermistor that monitors magnetron temperature, and when its resistance drops below the expected range, the control board triggers this fault code. The appliance shuts down magnetron operation to prevent potential damage. Replacing the NTC sensor is the recommended first step in resolving this fault.
Is it safe to use my Frigidaire range while the F098 code is active?
The F098 fault will disable magnetron operation, so the microwave function of the range will not work while the code is active. Standard oven and cooktop functions may still be available depending on your model. You should not attempt to bypass the fault, as the sensor exists to protect the magnetron from overheating. Address the fault before resuming microwave use.
How much does it cost to repair a Frigidaire range F098 error?
Repair costs depend on whether the issue is limited to the NTC sensor or involves additional components like the wiring harness or control board. The NTC sensor part itself is relatively inexpensive, typically in the range of $15 to $50. If professional labor is required, total repair costs including diagnosis and labor generally fall in the range of $100 to $250. Costs increase significantly if the control board also needs replacement.
Can I fix the F098 error myself?
Replacing the NTC sensor is a parts-based repair that some experienced DIYers can perform, but it does involve working near the magnetron, which stores high voltage even after the unit is unplugged. The capacitor in the magnetron circuit can retain a dangerous charge. For safety, this repair is best handled by a qualified appliance technician unless you have specific experience discharging high-voltage capacitors.
Will resetting the range clear the F098 error code?
A power reset, such as unplugging the unit or cycling the circuit breaker for a few minutes, may temporarily clear the code, but it will return as soon as the control board re-reads the shorted sensor signal. A reset does not fix the underlying hardware failure. The fault will persist until the faulty NTC sensor or any shorted wiring is physically repaired or replaced.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass