mypros+
Error code reference

GE Oven Error Code F7d

Lower CLEAR key stuck condition (Machine Control glass touch).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F7d error code actually means

The F7d error means your oven's control panel thinks the CLEAR button is being held down constantly, even when nobody is touching it. This is usually caused by a problem with the lower touch panel itself, not the main control board. Until this is fixed, the oven will not operate normally because it reads this stuck button as a hardware fault.

Diagnostic procedure

The full F7d procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Failure is most likely within the glass touch; replace glass touch.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F7d procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F7d

Ranked by how often they cause this code
  1. 1Failed glass touch panel assembly
  2. 2Moisture or debris under the glass touch surface
  3. 3Physical damage or deformation of the glass touch panel
  4. 4Faulty wiring connection between the glass touch and machine control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F7d

What does the F7d error code mean on a GE oven?
F7d on a GE oven means the machine control board has detected a stuck CLEAR key condition on the lower glass touch panel. The control system is receiving a continuous signal from that key, as if it is being pressed and held without release. This points to a fault within the glass touch assembly rather than the main control board.
Is it safe to use my GE oven when the F7d error is showing?
A stuck key condition on the glass touch panel will typically prevent the oven from operating normally, as the control system locks out input when it detects this fault. You should not attempt to bypass the error to force oven operation. Until the glass touch panel is replaced or the fault is resolved, the oven should not be used for cooking.
Can the F7d code on a GE oven be caused by something other than the glass touch panel?
In rare cases, a loose or damaged ribbon cable connector between the glass touch and the machine control board can produce a stuck key signal. Moisture or food residue under the glass surface is another possible cause. However, GE's diagnostic guidance identifies the glass touch assembly itself as the most likely source of F7d, so if cleaning and reseating connections do not clear the code, replacing the glass touch panel is the correct next step.
How do I fix the F7d error code on my GE oven?
Start by turning the oven off at the circuit breaker for 60 seconds, then restore power. If F7d returns, inspect the glass touch surface around the CLEAR key for moisture, debris, or physical damage and clean the area thoroughly. If the error persists after these steps, the glass touch panel assembly needs to be replaced. This part is specific to your oven model, so use your model number to source the correct assembly.
How much does it cost to fix F7d on a GE oven?
The glass touch panel assembly for GE ovens typically ranges from $80 to $200 depending on the model, and the part is usually available through GE Appliance Parts or appliance parts retailers. If you are comfortable with basic appliance disassembly, this is a DIY-friendly repair involving disconnecting a ribbon cable and swapping the panel. A professional repair technician would add a service call fee and labor, typically bringing the total to $200 to $400 or more depending on your region.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass