mypros+
Error code reference

Haier Air Conditioner Error Code E6

Thermistor on wiring board in short circuit (Power ON, Timing blinking, Running ON)

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E6 error code actually means

Your Haier air conditioner has detected a problem with a temperature sensor on its circuit board, and the sensor is giving an incorrect reading due to a short circuit. This causes the unit to stop working normally as a safety precaution. A technician will need to inspect the wiring connections and the sensor itself to get the system running again.

Diagnostic procedure

The full E6 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check contact of components and control board
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E6 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E6

Ranked by how often they cause this code
  1. 1Loose or disconnected thermistor connector
  2. 2Failed thermistor
  3. 3Damaged wiring insulation
  4. 4Corroded or contaminated connector terminals
  5. 5Faulty control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E6

What does E6 mean on a Haier air_conditioner?
E6 on a Haier air conditioner indicates that the thermistor on the wiring board has been detected in a short circuit condition. The control board monitors this thermistor to regulate temperatures, and when the circuit reads outside its expected resistance range, the unit shuts down and displays E6. The fault is visually identified by Power ON, Timing light blinking, and Running ON. Checking the thermistor connections and the control board is the recommended starting point for diagnosis.
Is it safe to keep running my Haier air conditioner with an E6 error?
No, you should not attempt to bypass or ignore the E6 error. The unit uses the wiring board thermistor to make critical decisions about its operating cycle, and running the system without accurate temperature data can lead to compressor damage or unsafe operating conditions. The unit's shutdown response to E6 is a protective measure.
How much does it cost to repair an E6 error on a Haier air conditioner?
Repair costs depend on the root cause. Reseating a loose connector costs nothing beyond a service call fee, which typically ranges from around $50 to $100. Replacing a thermistor is a relatively inexpensive parts repair, with parts and labor generally falling in the $75 to $200 range. If the control board is the cause, costs can rise to $150 to $400 or more depending on the model and labor rates in your area.
Can I fix the E6 error on my Haier air conditioner myself?
Some E6 errors are caused by nothing more than a loose connector, which a careful DIYer can reseat after disconnecting power to the unit. However, if the thermistor itself has failed or the wiring is damaged, replacing components inside the unit involves working with electrical parts and requires caution. If you are not comfortable working with appliance electronics, having a qualified technician handle the repair is the safer choice.
Will resetting my Haier air conditioner clear the E6 error?
A power reset may temporarily clear the E6 display, but the error will return if the underlying short circuit condition in the thermistor circuit has not been resolved. The root cause, whether it is a faulty thermistor, a damaged wire, or a loose connection, must be identified and corrected before the unit will operate normally and reliably.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass