mypros+
Error code reference

Haier Refrigerator Error Code Ed

Defrost heating issue; evaporator defrost sensor temperature did not rise above 7°C (44.6°F) after 60 minutes…

Haier codesHaier refrigerator codes

Defrost heating issue; evaporator defrost sensor temperature did not rise above 7°C (44.6°F) after 60 minutes of defrost cycle. Located at evaporator top right corner.

MyPros+ Max

Get the full diagnostic procedure for Ed.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Ed means on a Haier refrigerator

The Ed error code on a Haier refrigerator indicates a defrost heating fault. Specifically, the evaporator defrost sensor failed to detect a temperature rise above 7°C (44.6°F) within 60 minutes of the defrost cycle initiating. The defrost sensor is located at the top right corner of the evaporator coil and monitors temperature progression during the timed defrost cycle. When the system cannot confirm adequate heat delivery to the evaporator, it triggers this code to alert the technician that ice removal may be incomplete or that a heating component has failed.

The defrost system relies on a heating element to warm the evaporator coil and melt accumulated frost between cooling cycles. If the heater is open-circuit, the sensor will register little or no temperature rise during the full 60-minute window. A defective defrost sensor itself can also produce this fault if it reads falsely low temperatures even when the heater is functioning correctly. Additionally, a failed defrost relay or control board output that prevents the heater from energizing will produce the same symptom, since no heat is delivered regardless of the sensor's accuracy.

Heavy frost accumulation prior to the fault can sometimes extend melt time beyond the 60-minute threshold, though this is less common than a component failure. Technicians should verify heater continuity, sensor resistance, and control board relay output before condemning any single part. Leaving the Ed condition unresolved will result in progressive frost buildup on the evaporator, restricted airflow, and eventual loss of cooling performance throughout the refrigerator and freezer compartments.

Source: manufacturer service documentation.

Common causes of Ed

  1. 01

    Failed defrost heater

    Part replacement

    The defrost heater is the most common cause. An open-circuit heater produces no heat during the defrost cycle, so the sensor temperature never rises above the 7°C threshold. Check heater continuity with a multimeter; a good heater should show measurable resistance rather than an open line.

  2. 02

    Defective evaporator defrost sensor

    Part replacement

    The defrost sensor at the top right corner of the evaporator may be reading temperatures incorrectly, reporting values below 7°C even when adequate heat is present. Inspect the sensor for physical damage and verify its resistance value matches expected specifications at a known temperature.

  3. 03

    Defrost relay or control board fault

    Part replacement

    If the relay responsible for energizing the defrost heater is stuck open or the control board output is not sending voltage to the heater circuit, the heater will never activate. Test for proper voltage at the heater terminals during a forced defrost cycle to isolate this cause.

  4. 04

    Excessive frost buildup on evaporator

    Wiring / connection

    In rare cases, an unusually heavy accumulation of ice on the evaporator coil can require more than 60 minutes to fully melt, triggering the fault even with a functioning heater. This is more likely if a door seal has been leaking or the refrigerator was recently loaded with large amounts of warm food.

  5. 05

    Loose or corroded wiring connections

    Wiring / connection

    Poor electrical connections in the defrost heater circuit or sensor circuit can cause intermittent or total loss of function. Inspect the wiring harness and connectors near the evaporator for corrosion, moisture damage, or loose terminals.

See the test procedure for each cause

Frequently asked questions about Ed

What does Ed mean on a Haier refrigerator?
The Ed code means the refrigerator detected a defrost heating issue. The evaporator defrost sensor, located at the top right corner of the evaporator coil, did not register a temperature above 7°C (44.6°F) within 60 minutes of the defrost cycle starting. This points to a problem with the defrost heater, the sensor itself, or the circuit that powers them.
Can I fix the Ed error code myself?
Some basic checks are within reach of a knowledgeable DIYer, such as inspecting wiring connections and testing heater continuity with a multimeter. However, replacing the defrost heater, evaporator sensor, or control board requires accessing the evaporator compartment and working with electrical components, which is best handled by a qualified technician. Attempting repairs without proper tools or knowledge can cause further damage or create a safety hazard.
Is the Ed error code on a Haier refrigerator dangerous?
The Ed code itself does not represent an immediate safety emergency in most cases. However, a non-functioning defrost system will cause ice to accumulate on the evaporator coil over time, which reduces cooling efficiency and can eventually lead to food spoilage. It is best to address the fault promptly to avoid these secondary problems.
How much does it cost to repair the Ed error on a Haier refrigerator?
Repair costs vary depending on the failed component. A defrost heater replacement typically ranges from around $80 to $200 including parts and labor, while a defrost sensor is generally less expensive at roughly $50 to $130. Control board replacement is the most costly scenario, often ranging from $150 to $400 or more. Diagnostic fees from a technician may apply separately.
Will resetting the refrigerator clear the Ed error code?
Performing a power reset by unplugging the refrigerator for a few minutes may temporarily clear the Ed code, but it will return if the underlying defrost system fault is not repaired. The code is triggered by a measurable condition during the defrost cycle, so it will reappear the next time the refrigerator attempts to defrost and the sensor temperature fails to reach 7°C within 60 minutes. A reset alone is not a fix.

Related Haier refrigerator codes

All Haier refrigerator codes
View all 26 Haier refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass