mypros+
Error code reference

Kenmore Dryer Error Code L07

Main PGM error (Gas Type).

Kenmore codesKenmore dryer codes

Main PGM error (Gas Type).

MyPros+ Max

Get the full diagnostic procedure for L07.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What L07 means on a Kenmore dryer

The L07 error code on a Kenmore gas dryer indicates a Main PGM (Program) error related to Gas Type configuration. This fault originates in the main control board, which stores programmed parameters that define how the dryer operates based on the type of gas supply connected, either natural gas or liquid propane (LP). When the control board detects a mismatch, corruption, or invalid state in this gas type configuration data, it triggers the L07 code and typically halts dryer operation to prevent unsafe or improper combustion behavior.

The main control board contains firmware and configuration settings that are set during manufacturing or field conversion. If those settings become corrupted, if the board loses its stored configuration, or if a gas conversion procedure was performed incorrectly, the board may no longer have a valid gas type parameter. This can also occur if the control board is replaced without being properly configured for the installed gas type, or if a firmware issue causes the stored value to become invalid.

Diagnosing L07 typically involves inspecting the control board for signs of damage, verifying whether the dryer has been converted from natural gas to LP or vice versa, and confirming that the correct conversion kit and settings were applied. In many cases, the main control board itself must be replaced or reprogrammed. This is not a sensor or mechanical fault, it is a software or configuration-level error tied directly to the gas burner control parameters stored on the board.

Source: manufacturer service documentation.

Common causes of L07

  1. 01

    Incorrect or incomplete gas type conversion

    Wiring / connection

    If the dryer was converted from natural gas to LP or vice versa without properly completing all required programming steps, the control board may store an invalid gas type value and trigger L07.

  2. 02

    Main control board configuration loss or corruption

    Part replacement

    Power surges, electrical spikes, or board aging can corrupt the stored gas type configuration on the main control board, causing it to report an invalid or unrecognized gas type setting.

  3. 03

    Replacement control board not configured for gas type

    Wiring / connection

    If the main control board was recently replaced, it may have been installed without being programmed for the correct gas type, leaving the configuration parameter in an invalid state.

  4. 04

    Faulty main control board

    Part replacement

    Internal failure of the control board's memory or processing components can prevent it from reading or maintaining the gas type parameter correctly, requiring board replacement.

See the test procedure for each cause

Frequently asked questions about L07

What does L07 mean on a Kenmore dryer?
L07 on a Kenmore gas dryer indicates a Main PGM error related to the Gas Type configuration stored on the main control board. The board is reporting that its gas type setting is missing, corrupted, or invalid. This prevents the dryer from operating safely and must be addressed before normal function can resume. It is not a mechanical failure but a software or configuration-level fault.
Can I fix the L07 error myself on a Kenmore dryer?
If the dryer was recently converted between natural gas and LP, verifying that all conversion steps were completed correctly is a reasonable starting point and does not require professional tools. However, if the control board has lost its programming or is internally faulty, repair typically requires a qualified technician to reconfigure or replace the board. Working near gas components also carries inherent safety risks that make professional service advisable for most homeowners.
Will resetting the dryer clear the L07 error code?
A simple power reset by unplugging the dryer for a few minutes may temporarily clear the display, but if the underlying gas type configuration on the control board is corrupted or invalid, the L07 code will return when the dryer is powered back on. A reset does not fix the root cause, which is a programming or board-level issue. Proper resolution requires addressing the configuration problem directly.
Is it safe to use my Kenmore dryer when L07 is displayed?
No, you should not attempt to operate a gas dryer while L07 is active. The error indicates the control board does not have a valid gas type configuration, which means it may not be able to regulate the gas burner correctly. Continuing to use the dryer under these conditions could create a risk of improper combustion or unsafe operation. Discontinue use until the fault is diagnosed and resolved.
How much does it cost to repair a Kenmore dryer L07 error?
Repair costs vary depending on the cause. If the fix involves completing a gas conversion procedure or reprogramming the control board, labor costs might range from around $75 to $150. If the main control board needs to be replaced, parts alone can range from $100 to $300 or more depending on the model, with total repair costs including labor potentially reaching $200 to $450. Getting a diagnostic estimate from a technician before committing to repairs is recommended.

Related Kenmore dryer codes

All Kenmore dryer codes
View all 105 Kenmore dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass