mypros+
Error code reference

Kenmore Dryer Error Code V00

Displays PGM version information (e.g., 1AES U-- d--).

Kenmore codesKenmore dryer codes

Displays PGM version information (e.g., 1AES U-- d--).

MyPros+ Max

Get the full diagnostic procedure for V00.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What V00 means on a Kenmore dryer

The V00 display on a Kenmore dryer is not an error code in the traditional sense. It is a diagnostic readout that presents the control board's programmed software version information. When triggered, the display shows a string such as "1AES U-- d--" which encodes the firmware revision loaded onto the electronic control board. This mode is accessed intentionally through a specific button sequence during diagnostic entry, and it serves as a reference point for identifying which software version is installed on the unit.

This display is relevant in situations where a technician needs to confirm whether the control board is running the correct firmware for a given model or production run. Different software versions may govern how the board interprets sensor inputs, manages cycle timing, or handles fault detection. If a board has been replaced and the new board carries a different program version, this readout allows the technician to document or verify that information.

Because V00 is informational rather than a fault indicator, it does not point to a failed component or a system malfunction. The dryer is not in an error state when this code appears. It simply means the user or technician has entered the program version display mode. No repair action is required as a result of seeing V00 alone. If the dryer is also exhibiting operational problems, those should be diagnosed through separate fault code retrieval procedures rather than treating V00 itself as the root cause.

Source: manufacturer service documentation.

Common causes of V00

  1. 01

    Intentional diagnostic mode entry

    Wiring / connection

    The most common reason V00 appears is that a technician or user has pressed a specific button combination that triggers the diagnostic menu, which displays the firmware version as the first readout. Exiting the diagnostic mode will clear the display.

  2. 02

    Accidental button sequence activation

    Wiring / connection

    Pressing certain control panel buttons in a particular order, even unintentionally, can activate the diagnostic mode and bring up the V00 version screen. Simply cycling the dryer off and back on typically returns the display to normal.

  3. 03

    Control board replacement requiring version verification

    Wiring / connection

    After a control board has been replaced, a technician may deliberately access V00 to confirm which program version is loaded on the new board and ensure it matches the requirements for the specific dryer model.

  4. 04

    Control board retaining diagnostic state after power interruption

    Wiring / connection

    In rare cases, a power fluctuation or interrupted power cycle may cause the control board to resume in a diagnostic display state. Performing a full power reset by unplugging the dryer for several minutes usually resolves this.

See the test procedure for each cause

Frequently asked questions about V00

What does V00 mean on a Kenmore dryer?
V00 on a Kenmore dryer is a program version display, not a fault code. It shows the firmware version stored on the electronic control board, typically formatted as a string like "1AES U-- d--". This readout appears when the dryer enters a specific diagnostic mode and does not indicate any malfunction with the appliance.
How do I clear the V00 display on my Kenmore dryer?
Because V00 is an informational display triggered by a diagnostic mode, you can usually clear it by pressing the Start or Power button to exit the mode, or by turning the dryer off and unplugging it for a few minutes before restarting. No repair procedures are needed to clear this display since it does not represent a fault condition.
Is it safe to use my Kenmore dryer when V00 is showing?
Yes, V00 does not indicate a safety issue or a component failure. The dryer is not malfunctioning when this code is present. If the dryer is otherwise operating normally, there is no risk associated with the V00 display appearing on the control panel.
Will resetting my Kenmore dryer clear the V00 code?
A power reset, accomplished by unplugging the dryer for several minutes and then restoring power, will typically exit the diagnostic mode and return the display to its normal state. If the dryer was placed into diagnostic mode through a button sequence, simply pressing the appropriate exit button or cycling the power should clear the V00 display.
How much does it cost to fix a V00 code on a Kenmore dryer?
There is no repair cost associated with V00 because it is not a fault code and does not indicate a broken component. The display is purely informational and reflects the firmware version on the control board. If a technician is accessing V00 as part of a broader diagnostic visit, service call fees can range from $50 to $150 depending on your region and the service provider.

Related Kenmore dryer codes

All Kenmore dryer codes
View all 105 Kenmore dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass