mypros+
Error code reference

Kenmore Washer Error Code F/14

Motor Control Unit error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F/14 error code actually means

Your Kenmore washer has detected a problem with the Motor Control Unit, which is the electronic board that powers and controls the spin motor. The washer has shut itself down because it keeps seeing abnormal electrical conditions and wants to avoid further damage. A technician will need to inspect the wiring and motor, and possibly replace the Motor Control Unit.

Diagnostic procedure

The full F/14 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Unplug washer or disconnect power, check wire harness connections between drive motor, MCU, and CCU, check motor continuity.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F/14 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F/14

Ranked by how often they cause this code
  1. 1Failed Motor Control Unit (MCU)
  2. 2Loose or damaged wire harness connections
  3. 3Drive motor winding failure
  4. 4Power supply voltage fluctuations
  5. 5CCU communication fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F/14

What does F/14 mean on a Kenmore washer?
The F/14 code indicates that the Motor Control Unit (MCU) has experienced an internal failure caused by repeating under-voltage, over-voltage, or over-current conditions. The MCU is the board that controls power delivery to the drive motor. The washer stops operation to prevent further damage when this condition is detected repeatedly. Diagnosis involves checking wiring connections between the motor, MCU, and CCU, as well as testing motor continuity.
Is it safe to keep using my washer when the F/14 code appears?
No, you should not continue running the washer while the F/14 code is active. The error indicates abnormal electrical conditions in the motor control circuit, and continued use risks damaging the drive motor, the MCU, or other connected components. Disconnect power and address the fault before attempting to run a cycle.
Will resetting my Kenmore washer clear the F/14 error code?
Unplugging the washer and restoring power may temporarily clear the fault display, but the F/14 code will return if the underlying problem has not been resolved. Because the MCU is detecting a repeating condition, a simple reset does not fix the root cause. The wiring, motor, and MCU all need to be properly diagnosed and any failed components repaired or replaced before the error will stay cleared.
Can I fix the F/14 error myself, or do I need a technician?
Some steps are DIY-friendly, such as unplugging the washer, reseating loose wire harness connections, and checking for visible wiring damage. Testing motor continuity with a multimeter is also within reach for experienced DIYers. However, if the MCU itself has failed, replacing it requires comfort with appliance electronics, and if you are unsure, calling a qualified technician is the safer option.
How much does it cost to repair an F/14 error on a Kenmore washer?
Repair costs vary depending on the failed component. If only wiring or connectors need attention, costs can be minimal. A replacement drive motor typically runs in the range of $100 to $250 for the part alone, while a replacement MCU board generally falls in the $100 to $200 range. Adding labor for a professional technician can bring total repair costs to $200 to $450 or more, depending on your location and the specific parts required.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass