Error code reference
KitchenAid Dishwasher Error Code Anti-Bacterial/Heavy + Normal Wash + China Gentle + Quick Rinse
Turbidity sensor failed to calibrate
Turbidity sensor failed to calibrate
MyPros+ Max
Get the full diagnostic procedure for Anti-Bacterial/Heavy + Normal Wash + China Gentle + Quick Rinse.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·KitchenAid Dishwasher
Anti-Bacterial/Heavy + Normal Wash + China Gentle + Quick Rinse on my KitchenAid KDTE334GPS
M+
Turbidity sensor failed to calibrate
From Tech Sheet W18552093, p.25:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure control board supply voltage at the test points. Expected: 12 VDC and 5 VDC; a drop below 4.75 VDC on the logic rail points to a failed onboard regulator.
3.Inspect all connectors on the main control for corrosion, thermal stress, or backed-out pins. Reseat each connector with the power disconnected.
Part WPW10804018
Electronic control board
Related KitchenAid dishwasher codes
All KitchenAid dishwasher codes →- 1 BlinkControl problem detected.
- 1-1Control detected pilot relay K400 stuck closed.
- 1-2Control software issue
- 10-1Dispenser electrical problem
- 10-2Vent wax motor electrical problem
- 10-3Drying fan error
- 2-1Control software issue
- 2-2Model has an LCD display and the control has been exchanged…
View all 108 KitchenAid dishwasher codes
- 3-1Open or faulty temperature sensor, open connector or…
- 3-2Shorted temperature sensing circuit
- 3-3OWI (Optical Water Indicator) soil sensor failure.
- 4-3Wash motor not running
- 4-4Wash motor failure
- 5-1Door switch stuck open
- 5-2Door switch stuck closed
- 6 BlinksWash motor problems detected.
- 6-1Low/no water (mechanical problem)
- 6-2Fill valve electrical problem
- 6-3Suds/Air in pump
- 6-4Float switch open
- 6-6Cool incoming water
- 6-7Flow meter problem
- 6-8Water softener regeneration valve electrical problem (water…
- 7-1No heat
- 7-2Heater stuck on
- 8 BlinksLow or no water detected.
- 8-1Slow drain
- 8-2Drain motor electrical problem
- 8-3Drain stuck on
- 8-4Drain motor electrical problem
- 9-1Diverter can't find position
- 9-2Diverter stuck on
- 9-3Diverter disk missing from sump.
- 9-4Lower spray arm error
- Add Rinse AidThe rinse aid dispenser is empty and needs to be refilled.
- Anti-Bacterial/HeavyDispenser current sense error
- Anti-Bacterial/Heavy + China GentleDry fan current sense error
- Anti-Bacterial/Heavy + China Gentle + Quick RinseDrain pump current sense error
- Anti-Bacterial/Heavy + China Gentle + Quick Wash + Quick RinseWash heater current sense error
- Anti-Bacterial/Heavy + Normal WashDrain solenoid current sense error
- Anti-Bacterial/Heavy + Normal Wash + China GentleTurbidity sensor out of range
- Anti-Bacterial/Heavy + Normal Wash + China Gentle + Quick Wash + Quick RinseFill sensing error
- Anti-Bacterial/Heavy + Normal Wash + Quick Wash + Quick RinseWash thermistor out of range
- Anti-Bacterial/Heavy + Quick RinseWater inlet valve current sense error
- Anti-Bacterial/Heavy + Quick WashWash pump current sense error
- CACancel Reset has been pressed, ending the cycle in progress…
- Check DrainThe dishwasher senses the drain stopper is not closed…
- China Gentle + Quick RinseMain Control Board Memory Corruption
- Control LockAll buttons are disabled; the Control Lock feature has been…
- DOOR OPENIndicates the door has been opened during a dishwasher…
- EEPROM Access Error LEDElectronics failure (EEPROM access error)
- ELECTRONICS FAILUREEEPROM Access Error
- F10E1Dispenser electrical problem
- F10E2Vent wax motor electrical problem
- F10E3Drying fan electrical problem
- F10E4Diverter cannot find positions
- F10E5Diverter leak (motor)
- F1E1Relay or triac failure on main control board (ACU).
- F1E2Damaged or corrupted memory on control board; incompatible…
- F2E1Control detected stuck keys in user interface (key switch…
- F2E2User interface cannot communicate with main control; loose…
- F3E1Open or shorted connection or component in temperature…
- F3E2Shorted connection or component in temperature sensing…
- F3E3OWI (Optical Water Indicator) failed calibration.
- F4E1Loose connection in wash motor circuit and/or faulty wash…
- F4E2Open connection in heater circuit, heater component open…
- F4E3Heater relay on control shorted or heater component shorted…
- F4E4Wash motor failure due to loose connection in wash motor…
- F5E1Door stuck open
- F5E2Control programmed to not start if it suspects the door…
- F6E1Low or no water to dishwasher (mechanical problem)
- F6E2Fill valve electrical problem
- F6E3Suds or air detected in pump
- F6E4Float switch stuck in overfill (open) position and/or…
- F6E6Incoming water temperature under 18°C/65°F (cool water…
- F6E7Disconnected or damaged flowmeter.
- F6E8Regen valve electrical problem
- F7E1No heat
- F7E2Heater stuck on
- F7E4RIF filter plugged
- F8E1Slow drain
- F8E2Fill valve electrical problem
- F8E3Very low water / suds / air in pump
- F8E4Overfill switch open
- F8E5Fill valve stuck open
- F8E6Flow meter disconnected or damaged
- F9E1Diverter can't find position
- F9E2Drain motor electrical problem
- F9E3Diverter disc missing
- F9E4Lower spray arm error
- FAILED TEMP SENSOR OR ELEMENTFailed heater element, temperature sensor failed, bad…
- Failed Temperature Sensor or Element LEDFailed heater element, temperature sensor failure, bad…
- FILL FAILUREWater supply valve turned off, inlet valve failed, low…
- Fill Failure LEDFill failure due to water supply valve turned off, failed…
- FLOOD SWITCH ACTIVATEDFlood sensor detected moisture due to lid not sealing…
- Flood Switch Activated LEDFlood switch activated due to lid not sealing, water valve…
- LdLatch and Door switch status indicator displayed for 5…
- MOTOR FAILUREMotor jammed, stator wiring damaged, hall sensor out of…
- Motor Failure LEDMotor failure due to jammed motor, damaged stator wiring…
- NO LED DISPLAYNo power to unit or power to one tub only, loose…
- Normal Wash + Quick WashUser Interface General Failure
- Normal Wash + Quick Wash + Quick RinseUser Interface stuck key
- OPThermistor connector is open (thermistor not connected to…
- PFPower failure
- SanitizedWhen the SANI RINSE option was selected, this indicator…
- SHThermistor is shorted (short circuit detected during…
- Water Temp >85C LEDWater temperature sensed greater than 85°C (185°F) due to…
- WATER TEMPERATURE SENSED GREATER THAN 185°FWater temperature sensed greater than 185°F (85°C) due to…
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass