Error code reference
KitchenAid Dishwasher Error Code Anti-Bacterial/Heavy + Quick Wash
Wash pump current sense error
Wash pump current sense error
MyPros+ Max
Get the full diagnostic procedure for Anti-Bacterial/Heavy + Quick Wash.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·KitchenAid Dishwasher
Anti-Bacterial/Heavy + Quick Wash on my KitchenAid KDTE334GPS
M+
Wash pump current sense error
From Tech Sheet W17897679, p.51:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure drain pump winding resistance at connector J7 on the main control. Expected: 12 to 16 ohms at room temperature.
3.Back-probe the pump driver output under load. Verify the board switches the pump at 120 VAC during the drain portion of the cycle.
Part W10876537
Drain pump assembly
Related KitchenAid dishwasher codes
All KitchenAid dishwasher codes →- 1 BlinkControl problem detected.
- 1-1Control detected pilot relay K400 stuck closed.
- 1-2Control software issue
- 10-1Dispenser electrical problem
- 10-2Vent wax motor electrical problem
- 10-3Drying fan error
- 2-1Control software issue
- 2-2Model has an LCD display and the control has been exchanged…
View all 108 KitchenAid dishwasher codes
- 3-1Open or faulty temperature sensor, open connector or…
- 3-2Shorted temperature sensing circuit
- 3-3OWI (Optical Water Indicator) soil sensor failure.
- 4-3Wash motor not running
- 4-4Wash motor failure
- 5-1Door switch stuck open
- 5-2Door switch stuck closed
- 6 BlinksWash motor problems detected.
- 6-1Low/no water (mechanical problem)
- 6-2Fill valve electrical problem
- 6-3Suds/Air in pump
- 6-4Float switch open
- 6-6Cool incoming water
- 6-7Flow meter problem
- 6-8Water softener regeneration valve electrical problem (water…
- 7-1No heat
- 7-2Heater stuck on
- 8 BlinksLow or no water detected.
- 8-1Slow drain
- 8-2Drain motor electrical problem
- 8-3Drain stuck on
- 8-4Drain motor electrical problem
- 9-1Diverter can't find position
- 9-2Diverter stuck on
- 9-3Diverter disk missing from sump.
- 9-4Lower spray arm error
- Add Rinse AidThe rinse aid dispenser is empty and needs to be refilled.
- Anti-Bacterial/HeavyDispenser current sense error
- Anti-Bacterial/Heavy + China GentleDry fan current sense error
- Anti-Bacterial/Heavy + China Gentle + Quick RinseDrain pump current sense error
- Anti-Bacterial/Heavy + China Gentle + Quick Wash + Quick RinseWash heater current sense error
- Anti-Bacterial/Heavy + Normal WashDrain solenoid current sense error
- Anti-Bacterial/Heavy + Normal Wash + China GentleTurbidity sensor out of range
- Anti-Bacterial/Heavy + Normal Wash + China Gentle + Quick RinseTurbidity sensor failed to calibrate
- Anti-Bacterial/Heavy + Normal Wash + China Gentle + Quick Wash + Quick RinseFill sensing error
- Anti-Bacterial/Heavy + Normal Wash + Quick Wash + Quick RinseWash thermistor out of range
- Anti-Bacterial/Heavy + Quick RinseWater inlet valve current sense error
- CACancel Reset has been pressed, ending the cycle in progress…
- Check DrainThe dishwasher senses the drain stopper is not closed…
- China Gentle + Quick RinseMain Control Board Memory Corruption
- Control LockAll buttons are disabled; the Control Lock feature has been…
- DOOR OPENIndicates the door has been opened during a dishwasher…
- EEPROM Access Error LEDElectronics failure (EEPROM access error)
- ELECTRONICS FAILUREEEPROM Access Error
- F10E1Dispenser electrical problem
- F10E2Vent wax motor electrical problem
- F10E3Drying fan electrical problem
- F10E4Diverter cannot find positions
- F10E5Diverter leak (motor)
- F1E1Relay or triac failure on main control board (ACU).
- F1E2Damaged or corrupted memory on control board; incompatible…
- F2E1Control detected stuck keys in user interface (key switch…
- F2E2User interface cannot communicate with main control; loose…
- F3E1Open or shorted connection or component in temperature…
- F3E2Shorted connection or component in temperature sensing…
- F3E3OWI (Optical Water Indicator) failed calibration.
- F4E1Loose connection in wash motor circuit and/or faulty wash…
- F4E2Open connection in heater circuit, heater component open…
- F4E3Heater relay on control shorted or heater component shorted…
- F4E4Wash motor failure due to loose connection in wash motor…
- F5E1Door stuck open
- F5E2Control programmed to not start if it suspects the door…
- F6E1Low or no water to dishwasher (mechanical problem)
- F6E2Fill valve electrical problem
- F6E3Suds or air detected in pump
- F6E4Float switch stuck in overfill (open) position and/or…
- F6E6Incoming water temperature under 18°C/65°F (cool water…
- F6E7Disconnected or damaged flowmeter.
- F6E8Regen valve electrical problem
- F7E1No heat
- F7E2Heater stuck on
- F7E4RIF filter plugged
- F8E1Slow drain
- F8E2Fill valve electrical problem
- F8E3Very low water / suds / air in pump
- F8E4Overfill switch open
- F8E5Fill valve stuck open
- F8E6Flow meter disconnected or damaged
- F9E1Diverter can't find position
- F9E2Drain motor electrical problem
- F9E3Diverter disc missing
- F9E4Lower spray arm error
- FAILED TEMP SENSOR OR ELEMENTFailed heater element, temperature sensor failed, bad…
- Failed Temperature Sensor or Element LEDFailed heater element, temperature sensor failure, bad…
- FILL FAILUREWater supply valve turned off, inlet valve failed, low…
- Fill Failure LEDFill failure due to water supply valve turned off, failed…
- FLOOD SWITCH ACTIVATEDFlood sensor detected moisture due to lid not sealing…
- Flood Switch Activated LEDFlood switch activated due to lid not sealing, water valve…
- LdLatch and Door switch status indicator displayed for 5…
- MOTOR FAILUREMotor jammed, stator wiring damaged, hall sensor out of…
- Motor Failure LEDMotor failure due to jammed motor, damaged stator wiring…
- NO LED DISPLAYNo power to unit or power to one tub only, loose…
- Normal Wash + Quick WashUser Interface General Failure
- Normal Wash + Quick Wash + Quick RinseUser Interface stuck key
- OPThermistor connector is open (thermistor not connected to…
- PFPower failure
- SanitizedWhen the SANI RINSE option was selected, this indicator…
- SHThermistor is shorted (short circuit detected during…
- Water Temp >85C LEDWater temperature sensed greater than 85°C (185°F) due to…
- WATER TEMPERATURE SENSED GREATER THAN 185°FWater temperature sensed greater than 185°F (85°C) due to…
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass