mypros+
Error code reference

KitchenAid Dishwasher Error Code ELECTRONICS FAILURE

EEPROM Access Error

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the ELECTRONICS FAILURE error code actually means

Your KitchenAid dishwasher has detected a problem with the memory chip inside its main control board, and it has shut down completely as a result. This means the dishwasher cannot run any cycles until the issue is resolved. Try unplugging the machine for 10 seconds to see if it resets, but if the error comes back, the control board will need to be replaced.

Diagnostic procedure

The full ELECTRONICS FAILURE procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Unplug dishwasher or disconnect power for 10 seconds, then plug back in. If error remains, replace electronic controller.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock ELECTRONICS FAILURE procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of ELECTRONICS FAILURE

Ranked by how often they cause this code
  1. 1Failed or corrupted EEPROM on the control board
  2. 2Transient power surge or voltage spike
  3. 3Control board component failure
  4. 4Power interruption during a write cycle

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about ELECTRONICS FAILURE

What does ELECTRONICS FAILURE mean on a KitchenAid dishwasher?
The ELECTRONICS FAILURE code on a KitchenAid dishwasher indicates an EEPROM access error on the main electronic control board. The EEPROM is a memory chip that stores operational data, and when the controller cannot read or write to it, the dishwasher shuts down completely. This error will prevent the dishwasher from running any wash cycles until it is resolved.
Is it safe to use my KitchenAid dishwasher when it shows an ELECTRONICS FAILURE error?
No, the dishwasher will not operate when this error is active, which means there is no risk of running a cycle with a faulty control state. The machine has intentionally locked itself out to prevent unpredictable behavior. You should avoid attempting to bypass the error and instead perform the recommended power reset or arrange for control board replacement.
Can I replace the KitchenAid dishwasher electronic controller myself?
Replacing the electronic controller is a moderate difficulty repair that involves disconnecting power, removing the inner door panel, and carefully unplugging wire harness connectors from the old board before installing the new one. Technicians with experience in appliance disassembly can often complete this repair without professional help. However, if you are not comfortable working around electrical components or identifying the correct replacement part for your model, hiring a qualified technician is the safer option.
Will resetting my KitchenAid dishwasher clear the ELECTRONICS FAILURE code?
Unplugging the dishwasher or disconnecting power for 10 seconds is the recommended first step and can clear the error if it was caused by a temporary power glitch. If the ELECTRONICS FAILURE code returns after power is restored, the reset has not resolved the underlying problem and the electronic controller will need to be replaced. A reset alone will not repair a physically damaged or corrupted EEPROM chip.
How much does it cost to fix a KitchenAid dishwasher ELECTRONICS FAILURE error?
If the error requires an electronic controller replacement, parts typically range from $150 to $350 depending on the specific model. Adding professional labor, total repair costs can fall in the range of $250 to $500 or more. If the error clears with a simple power reset and does not return, there is no parts cost involved.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass