mypros+
Error code reference

LG Washer Error Code E-22

Temperature sensor short error.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E-22 error code actually means

The E-22 code means your LG washer has detected a problem with the part that measures the water temperature inside the machine. The temperature sensor has an electrical fault that is sending bad information to the washer's computer, causing the machine to stop. A technician will need to inspect the sensor and its wiring to determine whether the sensor itself or the wiring connection needs to be repaired or replaced.

Diagnostic procedure

The full E-22 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if both terminals of the sensor are slightly shorted; remove the shorted part.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E-22 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E-22

Ranked by how often they cause this code
  1. 1Failed temperature sensor (internal short)
  2. 2Damaged or pinched wiring harness
  3. 3Corroded or contaminated connector terminals
  4. 4Faulty wiring connection at the control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E-22

What does E-22 mean on a LG washer?
E-22 on an LG washer indicates a temperature sensor short error. The washer's control board has detected that the terminals of the temperature sensor are shorted together, producing an invalid resistance reading. This prevents the machine from accurately monitoring water temperature, so it stops operation and displays the code. The sensor, its wiring, or the connector will need to be inspected and the shorted component removed or replaced.
Is it safe to keep using my washer with an E-22 error?
No, you should not continue running the washer while the E-22 code is active. A shorted temperature sensor means the control board cannot accurately track water temperature, which could result in water being heated beyond the intended range. Continuing to operate the machine in this condition risks damage to fabrics and potentially to internal components.
Will resetting the washer clear the E-22 error code?
A reset may temporarily clear the E-22 code, but the error will return as soon as the washer attempts to read the temperature sensor again if the underlying short has not been corrected. To permanently resolve the error, the shorted sensor terminal, wiring, or component must be physically identified and repaired or replaced before the code will stay clear.
Can I fix the E-22 error myself?
Some DIY repair is possible depending on the cause. If the short is in an accessible connector or a visible section of wiring, a knowledgeable DIYer can disconnect the sensor, inspect both terminals for bridging, and repair or replace the affected component. If the thermistor itself has failed internally, it will need to be replaced, which typically requires basic disassembly of the washer cabinet to access the sensor location.
How much does it cost to repair an E-22 error on an LG washer?
Repair costs vary depending on the root cause. If only the wiring or connector needs to be cleaned or repaired, costs are minimal, primarily the cost of your time or a service call fee ranging from $50 to $100. If the temperature sensor needs to be replaced, parts typically cost in the range of $15 to $50, and a professional repair including labor could run $100 to $200 depending on your location and the technician's rates.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass