mypros+
Error code reference

LG Washer Error Code E-32

Weight sensor short error.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E-32 error code actually means

Your LG washer is showing an E-32 error because it detected a problem with the part that measures how heavy your laundry load is. This sensor has developed an electrical short, meaning it is not working correctly and the washer cannot properly calculate the load. The machine has stopped to protect itself until this issue is resolved.

Diagnostic procedure

The full E-32 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if both terminals of the sensor are slightly shorted.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E-32 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E-32

Ranked by how often they cause this code
  1. 1Shorted weight sensor terminals
  2. 2Damaged or pinched wiring harness
  3. 3Moisture or corrosion in the connector
  4. 4Loose or improperly seated connector
  5. 5Faulty control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E-32

What does E-32 mean on a LG washer?
The E-32 code on an LG washer indicates a weight sensor short error. This means the control board has detected a short circuit in the weight sensor circuit, which is responsible for measuring the mass of the laundry load. The washer will stop operating until the fault is diagnosed and corrected. Common causes include a failed sensor, damaged wiring, or moisture in the connector.
Is it safe to use my LG washer while it shows E-32?
You should not continue using the washer while the E-32 code is active. The weight sensor is integral to how the machine calculates water fill levels and spin speed, and operating without accurate sensor data can lead to improper cycle performance. Additionally, an unresolved short circuit in the sensor wiring could potentially worsen over time.
Will resetting my LG washer clear the E-32 error code?
Performing a reset, such as unplugging the washer for a few minutes and restarting it, may temporarily clear the E-32 code. However, if the underlying short condition in the weight sensor circuit still exists, the code will return once the washer attempts to read the sensor again. A reset is useful for confirming whether the fault is intermittent, but it does not substitute for proper diagnosis and repair.
Can I fix the E-32 error myself on my LG washer?
Some steps are DIY-friendly, such as inspecting the sensor wiring harness for visible damage, reseating connectors, and cleaning corroded terminals. To properly diagnose the fault, you should check whether both terminals of the weight sensor are slightly shorted using a multimeter. If the sensor itself has failed, replacing it requires moderate disassembly and some comfort working with appliance wiring. If you are not confident working with electrical components, a qualified technician is recommended.
How much does it cost to repair the E-32 error on an LG washer?
Repair costs vary depending on the root cause. If only the weight sensor needs replacement, parts typically range from around $20 to $80 depending on the model. If a technician is needed for diagnosis and labor, total repair costs commonly fall between $100 and $250. Control board replacement, if required, can push costs higher, generally into the $150 to $400 range including parts and labor.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass