mypros+
Error code reference

LG Washer Error Code Ed3

Breakdown softener pump-the amount of fabric softener in the softener reservoir did not decrease; softener may have hardened after being left for a…

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Ed3 error code actually means

Your LG washer noticed that the fabric softener in the dispenser never went down during the wash cycle, which means the small pump that moves softener into the drum is not working. This is often caused by softener that has thickened and hardened inside the dispenser after sitting unused for a long time. Cleaning out the dispenser or replacing the pump is usually how this gets fixed.

Diagnostic procedure

The full Ed3 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if detergent/softener pump connector is connected; check pump resistance (22-42 ohms ±10% between pin 1 and pin 3).
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Ed3 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Ed3

Ranked by how often they cause this code
  1. 1Hardened or Crystallized Softener Blocking the Pump
  2. 2Disconnected or Faulty Pump Connector
  3. 3Failed Softener Pump Motor
  4. 4Wiring Harness Damage Between Control Board and Pump
  5. 5Clogged Softener Dispenser Inlet or Tubing

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Ed3

What does Ed3 mean on a LG washer?
The Ed3 code means the LG washer detected that the fabric softener level in the softener reservoir did not decrease during a wash cycle. This indicates the softener dispensing pump failed to move liquid into the drum. The most frequent cause is softener that has hardened inside the reservoir or pump after being left for a long time. An electrical fault or failed pump motor can also trigger this code.
Is it safe to keep using my LG washer when Ed3 is showing?
The washer can still run its wash cycles with the Ed3 code active, but it will not dispense fabric softener correctly until the fault is resolved. There is no immediate safety hazard to the machine or user. However, continuing to run cycles without addressing the issue could allow hardened softener buildup to worsen, potentially causing more extensive blockage over time.
Will resetting my LG washer clear the Ed3 error code?
A basic reset, such as unplugging the washer for a few minutes and restarting, will not permanently clear the Ed3 code if the underlying fault still exists. The code will return as soon as the washer runs a cycle and detects that the softener level has not changed. The error will only clear reliably once the actual cause, whether a blockage, a loose connector, or a failed pump, has been corrected.
How do I fix the Ed3 error on my LG washer?
Start by removing the softener dispenser drawer and cleaning it thoroughly with warm water to dissolve any hardened residue. Next, check that the pump wiring connector is fully plugged in and free of damage. If cleaning and reconnecting the connector do not resolve the issue, use a multimeter to measure pump resistance between pin 1 and pin 3: the reading should fall between 22 and 42 ohms, plus or minus 10 percent. A reading outside that range means the pump motor needs to be replaced.
How much does it cost to repair an Ed3 error on an LG washer?
If the issue is simply hardened softener, the repair costs nothing beyond your time and some warm water for cleaning. A replacement softener pump, if the motor has failed, typically costs in the range of 20 to 60 dollars for the part itself. If you hire a technician for diagnosis and replacement, total repair costs including labor generally fall somewhere between 80 and 200 dollars depending on your location and the service provider.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass