mypros+
Error code reference

LG Washer Error Code EE1

Switch error

LG codesLG washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the EE1 error code actually means

Your LG washer's EE1 error means the machine thinks the power button has been held down for too long, which is usually caused by something pressing on that button area inside the control panel rather than you actually holding the button. This is often caused by screws inside the panel being too tight, which bends the panel and pushes the button contact constantly. It is not typically a safety emergency, but the washer will not operate normally until the issue is resolved.

Diagnostic procedure

The full EE1 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check if sub PBA screws are tightened too much.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock EE1 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of EE1

Ranked by how often they cause this code
  1. 1Sub PBA screws overtightened
  2. 2Control panel deformation
  3. 3Physically stuck or damaged power button
  4. 4Improper panel reassembly after prior repair
  5. 5Faulty sub PBA

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about EE1

What does EE1 mean on a LG washer?
The EE1 code on an LG washer indicates a switch error where the power button has been detected as continuously pressed for more than 12 seconds, or the switch is receiving uneven pressure due to control panel deformation. This is a control panel and sub PBA level fault, not a motor or drain issue. The machine registers the fault because it interprets the sustained button signal as an abnormal condition.
Is it safe to use my LG washer when it shows EE1?
The EE1 error is a control panel fault and the washer will typically not operate normally while this code is active. It is not a hazard related to water leakage or electrical shock risk in most cases, but you should not attempt to force operation while the fault persists. Resolve the underlying panel or switch issue before running a wash cycle.
How much does it cost to repair an EE1 error on a LG washer?
If the fix involves simply loosening the sub PBA screws, there is no parts cost and the repair can be done without a service call. If the control panel needs replacement due to warping or damage, parts typically range from $50 to $150 depending on the model, plus labor if a technician is involved. A full sub PBA replacement can add to that cost if the board itself is at fault. Getting a diagnostic visit from a technician usually runs between $75 and $150 before parts.
How do I fix the EE1 error on my LG washer?
Start by checking whether the screws securing the sub PBA are overtightened, as this is the first recommended diagnostic step and a common cause of the error. If the screws are too tight, loosen them slightly and check whether the error clears. Also inspect the control panel for any visible warping or deformation that could be pressing on the power button area. If mechanical causes are ruled out, the sub PBA or control panel assembly may need replacement.
Will resetting my LG washer clear the EE1 error?
A power cycle or reset may temporarily clear the EE1 display, but if the underlying cause, such as an overtightened sub PBA screw or a deformed control panel, is still present, the error will return. A reset alone is not a fix for this fault. The physical condition of the control panel and sub PBA mounting must be addressed for the error to stay cleared.

Related LG washer error codes

All LG washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass