mypros+
Error code reference

Maytag Dryer Error Code d-26

UI is not receiving communications from CCU (cycles and price display disabled while error persists or is…

Maytag codesMaytag dryer codes

UI is not receiving communications from CCU (cycles and price display disabled while error persists or is manually cleared).

MyPros+ Max

Get the full diagnostic procedure for d-26.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What d-26 means on a Maytag dryer

Error code d-26 on a Maytag dryer indicates that the User Interface (UI) board is not receiving communications from the Central Control Unit (CCU). These two boards form the core control architecture of the dryer: the CCU handles cycle logic, motor control, and sensor inputs, while the UI board manages the display, button inputs, and user-facing feedback. When the communication link between them breaks down, the UI has no data to display, which is why cycle selection and price display functions are disabled for the duration of the fault.

This communication typically occurs over a dedicated serial data line or harness connecting the two control boards. A failure anywhere along this path, including the wiring harness, connectors, or the boards themselves, can interrupt the signal and trigger d-26. The error persists until the underlying issue is corrected or the code is manually cleared through the control panel reset procedure.

Common causes include loose or corroded connector pins on the communication harness, a damaged wiring harness between the UI and CCU, a failed CCU that is no longer transmitting data, or a failed UI board that cannot receive or interpret the incoming signal. In some cases, a power fluctuation or software glitch may cause a temporary communication dropout that resolves after a reset. If the error returns after clearing, a hardware fault in the harness or one of the control boards is the likely culprit.

Source: manufacturer service documentation.

Common causes of d-26

  1. 01

    Loose or disconnected communication harness connector

    Wiring / connection

    The wiring harness that links the UI board to the CCU can work loose over time due to vibration. Inspect both ends of the harness for connectors that are partially unseated or have backed-out pins.

  2. 02

    Damaged or shorted wiring harness

    Part replacement

    The harness between the two boards can develop breaks, pinches, or shorts, especially where it routes around sharp cabinet edges or moving components. A visual inspection and continuity check of each wire in the harness can confirm damage.

  3. 03

    Failed Central Control Unit (CCU)

    Part replacement

    If the CCU has failed internally, it may stop transmitting data entirely, causing the UI to log d-26. A failed CCU typically cannot be repaired and requires replacement.

  4. 04

    Failed User Interface (UI) board

    Part replacement

    The UI board itself may have failed and lost the ability to receive or process the incoming communication signal from the CCU. This is typically diagnosed after the harness and CCU have been ruled out.

  5. 05

    Temporary software or power glitch

    Wiring / connection

    A brief power fluctuation or software fault can cause a one-time communication dropout. Manually clearing the code or performing a power cycle may resolve the issue if no hardware fault is present.

See the test procedure for each cause

Frequently asked questions about d-26

What does d-26 mean on a Maytag dryer?
Error code d-26 means the User Interface board is not receiving communications from the Central Control Unit. As a result, cycle selection and display functions are disabled while the error is active. The fault points to a breakdown in the communication path between the two main control boards, which can be caused by wiring, connector, or board-level failures.
Can I fix d-26 myself, or do I need a technician?
Some causes of d-26 are DIY-friendly, such as reseating a loose harness connector or performing a control reset. However, if the wiring harness is damaged or a control board has failed, the repair requires sourcing the correct parts and comfort working with appliance electronics. If you are unsure about diagnosing control board faults, a qualified technician is recommended.
Is it safe to use my Maytag dryer while d-26 is showing?
With d-26 active, cycles and display functions are disabled, so the dryer will not operate normally. Attempting to force operation while the UI and CCU are not communicating is not recommended, as the control system cannot properly manage the cycle. Address the fault before resuming regular use.
How much does it cost to repair a d-26 error on a Maytag dryer?
Repair costs depend on the root cause. Reseating a connector costs nothing beyond your time. A replacement wiring harness typically runs in the range of $20 to $60 for parts. A new CCU or UI board can cost anywhere from $80 to $250 or more for the part alone, with additional labor costs if a technician performs the repair.
Will resetting my Maytag dryer clear the d-26 error?
A manual reset or power cycle can clear the d-26 code if the original cause was a temporary communication glitch. However, if the error returns after the reset, a physical fault in the harness, connectors, or one of the control boards is present and must be corrected. Clearing the code repeatedly without fixing the underlying issue will not resolve the problem.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass