mypros+
Error code reference

Maytag Dryer Error Code 0

No code present (no fault detected).

Maytag codesMaytag dryer codes

No code present (no fault detected).

MyPros+ Max

Get the full diagnostic procedure for 0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 0 means on a Maytag dryer

Error code 0 on a Maytag dryer indicates that no fault has been detected by the control board. This is a normal status reading rather than a true error condition. When the dryer's diagnostic system is accessed or the display cycles through codes, a reading of 0 simply confirms that no active or stored fault codes are present in the control board's memory at that time.

The Maytag dryer control board continuously monitors key systems including the thermal fuse circuit, moisture sensor, motor relay, door switch, and heating element circuit. When all monitored components are operating within expected parameters, the system logs no fault and code 0 is the result. This reading can appear during a manual diagnostic cycle initiated by pressing specific button sequences, or it may be displayed briefly as the board initializes.

If code 0 appears while the dryer is experiencing a performance issue such as not heating, not starting, or not drying efficiently, the problem may be mechanical rather than electronic. Issues like a clogged exhaust duct, worn drum belt, or a failed component that does not have a dedicated sensor may not trigger a fault code. In these cases, a hands-on inspection of airflow, belt tension, and heating components is the appropriate next step rather than relying on the diagnostic code display.

Source: manufacturer service documentation.

Common causes of 0

  1. 01

    Normal diagnostic system readout

    Wiring / connection

    Code 0 most commonly appears during a self-diagnostic cycle to confirm no faults are stored. This is expected behavior and requires no action.

  2. 02

    Clogged exhaust ductwork

    Wiring / connection

    If the dryer runs but performs poorly, a restricted exhaust duct can cause issues without triggering a fault code. Check the full length of the duct for lint buildup or kinks.

  3. 03

    Worn or broken drum belt

    Part replacement

    A failed drum belt may prevent the drum from turning without triggering an electronic fault code. Listen for the motor running while the drum stays still as a key indicator.

  4. 04

    Mechanical door latch failure

    Part replacement

    A door latch that does not engage properly may prevent the dryer from starting without logging an error if the switch itself is still functional. Inspect the latch strike and catch for wear or misalignment.

  5. 05

    Control board successfully cleared after a previous fault

    Wiring / connection

    After a fault is resolved and the board is reset, code 0 confirms the memory has been cleared. This is the intended outcome following a successful repair.

See the test procedure for each cause

Frequently asked questions about 0

What does 0 mean on a Maytag dryer?
Code 0 on a Maytag dryer means no fault has been detected or stored by the control board. It is a normal status indicator, not an error condition. It typically appears when you run a diagnostic cycle and the dryer's systems are all functioning within acceptable parameters.
Do I need to fix anything if my Maytag dryer shows code 0?
If the dryer is operating normally, code 0 requires no action at all. However, if the dryer is behaving abnormally despite showing code 0, the underlying issue is likely mechanical rather than electronic. In that case, inspect components like the exhaust duct, drum belt, and door latch, since these may fail without triggering a stored fault code.
Is it safe to use my Maytag dryer when it shows code 0?
Yes, code 0 indicates no fault is present, so from an electronics standpoint the dryer is safe to operate. If you are seeing code 0 alongside unusual behavior such as overheating or excessive drying times, check the exhaust vent for blockages before continuing use, as restricted airflow can create a fire hazard over time.
Will resetting my Maytag dryer clear code 0?
Code 0 does not need to be cleared because it is not an error. If you previously had a fault code and performed a reset, code 0 appearing afterward confirms the board's memory was successfully cleared. No further reset is necessary.
How much does it cost to repair a Maytag dryer showing code 0?
Since code 0 is not an error, there is typically no repair cost associated with it directly. If a mechanical problem is found during a follow-up inspection, repair costs will depend on the failed component. Common repairs such as a drum belt replacement generally range from $50 to $150 in parts and labor, while more involved repairs can run higher.

Related Maytag dryer codes

All Maytag dryer codes
View all 251 Maytag dryer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass