mypros+
Model reference

Amana 5P-2M-1W

Air Conditioner

1 document59 error codes17 service modes

Available documentation

Tech Sheet

  • Service Guide - Tech Sheet W1117522244 pg
    Covers this model
MyPros+ Max

Diagnose your Amana 5P-2M-1W.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (59)

CodeMeaning
:Power failure indication0No code present (no fault detected).14Heater on and drum temperature not increasing.15Thermistor out of range.16Thermistor possible open.17Thermistor possible short.18Motor thermal protector opened more than 5 times during cycle.20Dryer over temp without shutdown.21Selected dryer temperature not reached.22Dryness sensor bar possibly open.23Dryness sensor bar possibly shorted.24Incorrect rotary switch position seen.25Rotary Switch 1 left of encoder failed at startup.26Rotary Switch 2 left of encoder failed at startup.28Rotary Switch 3 left of encoder failed at startup.3Door switch error (power failure / door switch code).31Model ID Unknown, default used at startup.F0 E7Low Voltage ErrorF1 E1ACU (Appliance Control Unit) Fault.F1 E4UIC (User Interface Control) Fault.F1 E7Voltage Input Fault.F1:CFHardware configuration mismatch between electronic control board and display…F1:E4Microwave relay failure.F1:PrSoftware type mismatch in electronic control board.F1E1No voltage detected at the heater relay or main control (ACU) problem.F2Touch panel failure.F2 E1Dryer keypad is sensed pressed for 10 seconds (stuck key error); fault will…F2 E2Upper Dryer Keypad Stuck ErrorF2:E1Keyboard failureF2E1Stuck button on HMI detected (depressed for over 20 seconds).
View all 59 error codes
F2E2The HMI has detected an internal fault.F3E1Exhaust thermistor is open (>50k ohms below 18°F) or shorted (<500 ohms above…F3E2Moisture sensor strip is open or shorted.F3E3Inlet thermistor is open (>245k ohms below 18°F) or shorted (<328 ohms above…F3E5Rear moisture sensor strip is open or shortedF3HHumidity sensor failure.F4:E1Magnetron temperature sensor failure (software error).F5 E1Dryer Door Circuit Error.F5 E6Upper Dryer Door Circuit ErrorF6Microwave relay failure.F6 E1Communication Failure Between ACU and UICF6:E0Communication error between display board and electronic control board.F6E1Communication between the HMI and ACU has not been detected.F7 E6Lower Dryer Motor Circuit ErrorF7 E7Upper Dryer Motor Circuit ErrorF7 E8Lower Dryer Motor Sense ErrorF7 E9Upper Dryer Motor Sense ErrorFC E1Model/Serial number not programmed on the control.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi Connection Fault.FC E4USB FaultFC E5Software Update FailureFC E6Model Setup Export FailureFC E7Model Setup Import FailureFC E8Wi-Fi Module not responding or not connected.FP E1Coin 1 Circuit Error.FP E2Coin 2 Circuit Error.FP E3Card Reader Communication error.noCFSoftware configuration error in display board.

Service modes (17)

  • Console Switch Test["Enter Service Mode.","Set Cycle Selection Knob to 'Wrinkle Prevent' and press knob.","Power Off…
  • diagnostic["Plug in microwave oven or reconnect power.","Press Stop button to enter standby (displays…
  • Diagnostic Cycle (Factory)["Enter Service Mode.","Navigate to Factory Diagnostics.","Select Diagnostic Cycle.","Press the…
  • Diagnostic Cycle (Service)["Enter Service Mode.","Navigate to Service Diagnostics.","Select Diagnostic Cycle.","Press the…
  • Diagnostic Mode["Enter setup mode first.","Navigate to any of the set-up codes 1 through 6 (or while dAS displays…
  • Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • Display/Clear Service Codes["Enter Service Mode.","Set Cycle Selection Knob to 'Time Dry 10' and press knob.","Time Dry 10 LED…
  • Help Mode["Enter setup mode first.","Navigate to special pricing option step 2.XX (or while dAS displays if…
  • Model/Serial Number Menu["Enter Help Mode first.","While on the S0 screen, press the HEAVY DUTY keypad.","Use NORMAL keypad…
  • Service Cycle["Enter Service Mode.","Set Cycle Selection Knob to 'Regular' and press knob.","Cool Down LED…
  • Service Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Mode Entry["Rotate the Cycle Selector Knob to the 'Power Off' position and press knob (all LEDs will be…
  • Setup Mode["PD Models
  • Setup Mode (Control Set-Up)["PD Models
  • Touch Panel and Electronic Control Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • USB Menu["Enter Help Mode first.","While on the USB screen, press the HEAVY DUTY keypad.","Use NORMAL…
  • Wi-Fi Menu["Enter setup mode and navigate to the F0 screen.","Press the HEAVY DUTY keypad to enter Wi-Fi…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass