mypros+
Error code reference

Miele Dishwasher Error Code F0

No fault detected in the electronic controls.

Miele codesMiele dishwasher codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F0 error code actually means

The F0 code on your Miele dishwasher is simply the machine's way of saying everything is fine with its electronics and no errors have been found. Think of it as a clean bill of health from the control system. If your dishwasher is still not performing correctly despite this code, the issue is likely something mechanical, like a clogged filter or blocked spray arm, rather than an electronic fault.

Diagnostic procedure

The full F0 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F0 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F0

Ranked by how often they cause this code
  1. 1Diagnostic mode readout
  2. 2Fault memory recently cleared
  3. 3Non-electronic performance issue
  4. 4Intermittent fault no longer active

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F0

What does F0 mean on a Miele dishwasher?
F0 means no fault has been detected in the electronic controls. It is a status indicator, not an error, and it appears when the control board completes a diagnostic check and finds no active or stored faults. It is most commonly seen when accessing the service or diagnostic menu.
Is it safe to run my Miele dishwasher when it shows F0?
Yes, F0 indicates no electronic fault is present, so the machine is safe to operate. If the dishwasher is running normally and displaying F0 during a diagnostic check, you can continue using it without concern. Only investigate further if you notice a specific performance problem.
How much does it cost to fix a Miele dishwasher showing F0?
There is no repair cost associated with F0 because it is not a fault code. If the machine has an underlying mechanical issue that F0 does not account for, repair costs will depend on the specific component involved and could range from a nominal service call fee to several hundred dollars for parts and labor on components like the water inlet valve or pump assembly.
Do I need to fix anything if my Miele dishwasher shows F0?
No repair is needed for F0 itself, as it confirms the electronics are functioning correctly. However, if your dishwasher is experiencing a performance problem despite showing F0, you should inspect mechanical components such as the drain filter, spray arms, and water inlet for blockages or damage. F0 only clears the electronic systems from suspicion.
Will resetting my Miele dishwasher clear the F0 code?
F0 is not a fault code that needs to be cleared. It simply reports a clean status from the control board. A power cycle or reset may cause it to disappear from the display, but it will return any time the diagnostic mode is accessed and no faults are found.

Related Miele dishwasher error codes

All Miele dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass